////////////////////////// // RP2040-Decoder // // Gabriel Koppenstein // // core1.c // ////////////////////////// #include "core1.h" struct repeating_timer pid_control_timer, speed_helper_timer; // Get speed_step_table_index depending on speed_step uint8_t get_speed_step_table_index_of_speed_step(uint8_t speed_step) { // Clear direction information in bit7 speed_step = speed_step & 0b01111111; // Check for Stop or Emergency Stop speed step if (speed_step == 0 || speed_step == 1) { return 0; } // In any other case i.e. speed steps 1 to 126: return speed_step-1; } // This function gets called every x milliseconds where x is CV_175. // The purpose of this function is to implement a time delay in acceleration or deceleration bool speed_helper(struct repeating_timer *const t) { // pid->setpoint only gets adjusted when the speed_helper_counter is equal to the accel_rate/decel_rate // -> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate) or CV_175*CV_3 or CV_175*CV_4 pid_params *const pid = (pid_params *) (t->user_data); const uint8_t accel_rate = CV_ARRAY_FLASH[2]; const uint8_t decel_rate = CV_ARRAY_FLASH[3]; static uint8_t speed_helper_counter; static uint8_t speed_table_index; // Get speed_step_table_end_index corresponding to current speed_step_target const uint8_t speed_step_table_end_index = get_speed_step_table_index_of_speed_step(speed_step_target); const bool direction_changed = get_direction_of_speed_step(speed_step_target) != get_direction_of_speed_step(speed_step_target_prev); if (pid->speed_step_target == 129 || pid->speed_step_target == 1) { // Emergency Stop speed_table_index = 0; speed_helper_counter = 0; pid->setpoint = pid->speed_table[speed_table_index]; } else if (speed_step_table_end_index > speed_table_index && speed_helper_counter == accel_rate) { // Acceleration if (!accel_rate) speed_table_index = speed_step_table_end_index; // directly accelerate to end target speed else speed_table_index++; pid->setpoint = pid->speed_table[speed_table_index]; speed_helper_counter = 0; } else if (speed_step_table_end_index < speed_table_index && speed_helper_counter == decel_rate) { // Deceleration if (!decel_rate) speed_table_index = speed_step_table_end_index; // directly decelerate to end target speed else speed_table_index--; pid->setpoint = pid->speed_table[speed_table_index]; speed_helper_counter = 0; } else if (direction_changed) { // Change of direction while decelerating -> jump to most recent speed_step without delay (other direction) speed_table_index = speed_step_table_end_index; pid->setpoint = pid->speed_table[speed_table_index]; speed_helper_counter = 0; } else if (speed_step_table_end_index != speed_table_index) { // Acceleration/Deceleration "scheduled" speed_helper_counter++; } else { // Target reached -> Reset Counter speed_helper_counter = 0; } // return true to schedule the repeating timer again return true; } // Helper function to adjust pwm level/duty cycle. void adjust_pwm_level(const uint16_t level) { if (get_direction_of_speed_step(speed_step_target)) { // Forward pwm_set_gpio_level(MOTOR_REV_PIN, 0); pwm_set_gpio_level(MOTOR_FWD_PIN, level); } else { // Reverse pwm_set_gpio_level(MOTOR_FWD_PIN, 0); pwm_set_gpio_level(MOTOR_REV_PIN, level); } } // Update feed-forward slope/gradient for both directions void update_m(pid_params *const pid) { pid->m_fwd = (pid->y_2_fwd - pid->y_1_fwd) / (pid->x_2_fwd - pid->x_1_fwd); pid->m_rev = (pid->y_2_rev - pid->y_1_rev) / (pid->x_2_rev - pid->x_1_rev); } // Update feedforward function value y_2 in both directions void update_y(pid_params *const pid, const float i) { if (get_direction_of_speed_step(speed_step_target)) { // Forward pid->y_2_fwd += i * pid->k_ff; // Limit y_2_fwd if (pid->y_2_fwd > pid->max_output) pid->y_2_fwd = pid->max_output; else if (pid->y_2_fwd < pid->y_1_fwd) pid->y_2_fwd = pid->y_1_fwd; } else { // Reverse pid->y_2_rev += i * pid->k_ff; // Limit y_2_rev if (pid->y_2_rev > pid->max_output) pid->y_2_rev = pid->max_output; else if (pid->y_2_rev < pid->y_1_rev) pid->y_2_rev = pid->y_1_rev; } update_m(pid); } // Returns feedforward value corresponding to current setpoint float get_ff_val(const pid_params *const pid) { float val; if (get_direction_of_speed_step(speed_step_target)) { // Forward val = pid->m_fwd * ((float) pid->setpoint - pid->x_1_fwd) + pid->y_1_fwd; } else { // Reverse val = pid->m_rev * ((float) pid->setpoint - pid->x_1_rev) + pid->y_1_rev; } return val; } // Returns proportional gain value corresponding to current setpoint float get_kp(const pid_params *const pid) { const float sp = (float) pid->setpoint; if (sp < pid->k_p_x_1) { return pid->k_p_m_1 * sp + pid->k_p_y_0; } return pid->k_p_m_2 * (sp - pid->k_p_x_1) + pid->k_p_y_1; } // PID controller function gets called every x milliseconds where x is CV_49 aka sampling time (pid->t) bool pid_control(struct repeating_timer *const t) { // Cast (void *) to (pid_params *) pid_params *const pid = (pid_params *) (t->user_data); // Acceleration from standstill or change in direction -> reset previous derivative, error and integral parts const bool direction_changed = get_direction_of_speed_step(speed_step_target) != get_direction_of_speed_step(speed_step_target_prev); if ((!pid->setpoint_prev && !pid->setpoint) || direction_changed) { pid->d_prev = 0.0f; pid->i_prev = 0.0f; pid->e_prev = 0.0f; } // Get feed-forward and proportional gain values const float feed_fwd = get_ff_val(pid); pid->k_p = get_kp(pid); // Measure BEMF voltage and compute error pid->measurement = measure(pid->msr_total_iterations, pid->msr_delay_in_us, pid->l_side_arr_cutoff, pid->r_side_arr_cutoff, get_direction_of_speed_step(speed_step_target)); const float measurement_corrected = pid->measurement - pid->adc_offset; const float e = (float) pid->setpoint - measurement_corrected; // Proportional part, integral part and derivative part (including digital low-pass-filter with time constant tau) const float p = pid->k_p * e; float i = pid->ci_0 * (e + pid->e_prev) + pid->i_prev; const float d = pid->cd_0 * (pid->measurement - pid->measurement_prev) + pid->cd_1 * pid->d_prev; // Check for limits on the integral part if (i > pid->int_lim_max) { i = pid->int_lim_max; } else if (i < pid->int_lim_min) { i = pid->int_lim_min; } // Sum feed forward + all controller terms (p+i+d). Limit Output from 0% to 100% duty cycle float output = feed_fwd + p + i + d; if (output < 0 || !pid->setpoint) { output = 0.0f; } else if (output > pid->max_output) { output = pid->max_output; } if (LOGLEVEL >= 1) { static int counter = 0; counter++; if (counter > 100) { LOG(1, "pid error(%f) output(%f)\n", e, output); counter = 0; } } // Set PWM Level and discard results in adc fifo adjust_pwm_level((uint16_t) roundf(output)); adc_fifo_drain(); // Check for High or Low Integrator values -> Update x,y values of feedforward function if ((output < pid->max_output && output > pid->max_output / 2) && ((i > pid->int_lim_max / 2) || (i < pid->int_lim_min / 2))) { update_y(pid, i); } // Save previous error, integrator, differentiator, direction, setpoint and measured value also sum error to e_sum pid->e_prev = e; pid->i_prev = i; pid->d_prev = d; pid->setpoint_prev = pid->setpoint; pid->measurement_prev = pid->measurement; // return true to schedule the repeating timer again return true; } // PID controller and measurement parameter, and speed_table initialization void init_pid(pid_params *const pid) { // Measurement variables initialization pid->adc_offset = (float) CV_ARRAY_FLASH[171]; pid->msr_total_iterations = CV_ARRAY_FLASH[60]; pid->msr_delay_in_us = CV_ARRAY_FLASH[61]; pid->l_side_arr_cutoff = CV_ARRAY_FLASH[62]; pid->r_side_arr_cutoff = CV_ARRAY_FLASH[63]; // Speed table initialization // Calculate speed setpoint table according to V_min, V_max and V_mid CVs const double v_min = (double) CV_ARRAY_FLASH[1]; const double v_mid = (double) CV_ARRAY_FLASH[5] * 16; const double v_max = (double) CV_ARRAY_FLASH[4] * 16; LOG(1, "speedtable min(%f) mid(%f) max(%f)\n", v_min, v_mid, v_max); const double delta_x = 63; const double m_1 = (v_mid - v_min) / delta_x; const double m_2 = (v_max - v_mid) / delta_x; pid->speed_table[0] = 0; for (uint8_t i = 1; i < 64; ++i) { pid->speed_table[i] = (uint16_t) lround(m_1 * (i - 1) + v_min); } for (uint8_t i = 64; i < 127; ++i) { pid->speed_table[i] = (uint16_t) lround(m_2 * (i - 63) + v_mid); } // Controller constants initialization pid->k_i = (float) CV_ARRAY_FLASH[49] / 10; pid->k_d = (float) CV_ARRAY_FLASH[50] / 10000; pid->tau = (float) CV_ARRAY_FLASH[47] / 1000; pid->t = (float) CV_ARRAY_FLASH[48] / 1000; pid->ci_0 = (pid->k_i * pid->t) / 2; pid->cd_0 = -(2 * pid->k_d) / (2 * pid->tau + pid->t); pid->cd_1 = (2 * pid->tau - pid->t) / (2 * pid->tau + pid->t); pid->int_lim_max = 10 * (float) CV_ARRAY_FLASH[51]; pid->int_lim_min = -10 * (float) CV_ARRAY_FLASH[52]; pid->k_ff = (float) CV_ARRAY_FLASH[46] / 10000; pid->max_output = (float) (_125M / (CV_ARRAY_FLASH[8] * 100 + 10000)); pid->x_1_rev = 0.0f; pid->x_1_fwd = 0.0f; pid->y_1_fwd = (float) get_16bit_CV(175); pid->y_1_rev = (float) get_16bit_CV(177); pid->x_2_rev = (float) pid->speed_table[126]; pid->x_2_fwd = (float) pid->speed_table[126]; // Controller variables initialization pid->y_2_fwd = pid->max_output; pid->y_2_rev = pid->max_output; pid->measurement = 0.0f; pid->measurement_prev = 0.0f; pid->e_prev = 0.0f; pid->i_prev = 0.0f; pid->d_prev = 0.0f; pid->setpoint = 0; // Gain scheduling initialization pid->k_p_x_1_shift = (float) CV_ARRAY_FLASH[59] / 255.0f; pid->k_p_x_1 = (float) pid->speed_table[126] * pid->k_p_x_1_shift; pid->k_p_x_2 = (float) pid->speed_table[126] * (1.0f - pid->k_p_x_1_shift); pid->k_p_y_0 = (float) get_16bit_CV(53) / 100.0f; pid->k_p_y_1 = (float) get_16bit_CV(55) / 100.0f; pid->k_p_y_2 = (float) get_16bit_CV(57) / 100.0f; pid->k_p_m_1 = (pid->k_p_y_1 - pid->k_p_y_0) / pid->k_p_x_1; pid->k_p_m_2 = (pid->k_p_y_2 - pid->k_p_y_1) / pid->k_p_x_2; update_m(pid); } void core1_entry() { LOG(1, "core1 init...\n"); pid_params pid_parameters; pid_params *pid = &pid_parameters; init_pid(pid); alarm_pool_add_repeating_timer_ms(alarm_pool_create(0, 1), CV_ARRAY_FLASH[48], pid_control, pid, &pid_control_timer); // Set TIMER_IRQ_0 to highest priority of 0x00 irq_set_priority(TIMER_IRQ_0, 0x00); alarm_pool_add_repeating_timer_ms(alarm_pool_create(1, 1), CV_ARRAY_FLASH[174], speed_helper, pid, &speed_helper_timer); LOG(1, "core1 done\n"); while (true); }