////////////////////////// // RP2040-Decoder // // Gabriel Koppenstein // // core0.c // ////////////////////////// #include "core0.h" // Define pointer to CV array stored in flash memory, FLASH_TARGET_OFFSET is defined in CMakeLists.txt and depending on flash size, // it gets stored in the highest address flash sector possible, to avoid interference with the program code. // CMakelists.txt also checks for program code exceeding past the last sector. Just have to make sure the correct flash size is set in CMakeLists.txt const uint8_t *CV_ARRAY_FLASH = (const uint8_t *) (XIP_BASE + FLASH_TARGET_OFFSET); // level_table is used to store pwm levels for any output using PWM uint16_t level_table[sizeof(uint32_t)*8] = {0}; // Volatile due to modification in gpio interrupt context volatile absolute_time_t falling_edge_time, rising_edge_time; // Input bit buffer for DCC signal uint64_t input_bit_buffer = 0; dcc_ring_buffer_t dcc_r_buf = {0}; static void increment_ring_buffer_idx(size_t * idx, uint8_t ring_buffer_length) { // Takes index variable as a pointer and increments it by 1. When index reaches the end of the ring buffer, it wraps around. // The wrap around value is the length of the ring buffer. *idx = (*idx + 1) % ring_buffer_length; } static size_t get_flash_size() { // Function to read the flash size of the chip, used for debugging/testing purposes // Prepare TX and RX buffers for reading the JEDEC ID uint8_t tx_buf[4] = { FLASH_CMD_READ_JEDEC_ID, 0, 0, 0 }; // Send the 0x9F command uint8_t rx_buf[4] = { 0, 0, 0, 0 }; // RX buffer for the response size_t buf_size = sizeof(tx_buf); void * params[] = {tx_buf, rx_buf, &buf_size}; int ret_val = flash_safe_execute(call_flash_do_cmd, params, FLASH_TIMEOUT_IN_MS); if (ret_val != PICO_OK){ set_error(FLASH_SIZE_READBACK_FAILURE); return 0; } // The third byte of the response (rxbuf[3]) contains the log2 size (e.g., 0x18 for 16 MB) if (rx_buf[3] == 0) { set_error(FLASH_SIZE_READBACK_FAILURE); return 0; } // Calculate the actual size (2^size_code bytes) size_t flash_size = (1u<> (sizeof(x) * 8 - 1); return (x + mask) ^ mask; } static uint16_t two_std_dev(const uint16_t arr[], const uint32_t length) { // Calculate arithmetic average uint64_t sum = 0; for (uint32_t i = 0; i < length; ++i) { sum += arr[i]; } const uint64_t x_avg = sum / length; // Calculate sample variance and sampled standard deviation sum = 0; for (uint32_t i = 0; i < length; ++i) { sum += (arr[i] - x_avg) * (arr[i] - x_avg); } const uint16_t variance = sum / (length-1); const uint16_t std_dev = (uint16_t) sqrtf((float) variance); // Sum every element that is within two times the sampled standard deviation and compute new average sum = 0; uint32_t counter = 0; for (uint32_t i = 0; i < length; ++i) { const uint32_t diff = absolute_val(arr[i] - x_avg); if ( diff <= 2*std_dev ){ sum += arr[i]; counter++; } } return sum / counter; } static void adc_offset_adjustment(uint32_t const n) { // Measures constant adc offset and programs the offset into flash LOG(1, "ADC offset adjustment with %u iterations...\n", n); uint16_t offsets_fwd[n]; uint16_t offsets_rev[n]; // Set PWM level to 0 just to be sure pwm_set_gpio_level(MOTOR_FWD_PIN, 0); pwm_set_gpio_level(MOTOR_REV_PIN, 0); busy_wait_ms(1000); // Measure n times in (reverse direction) LOG(1, "Measuring ADC offset in reverse direction (input channel: %u)...\n", REV_V_EMF_ADC_CHANNEL); adc_select_input(REV_V_EMF_ADC_CHANNEL); adc_run(true); for (uint32_t i = 0; i < n; i++) { offsets_rev[i] = adc_fifo_get_blocking(); } adc_run(false); adc_fifo_drain(); LOG(1, "Done measuring in reverse direction...\n"); busy_wait_ms(1000); // Measure n times in (forward direction) LOG(1, "Measuring ADC offset in forward direction (input channel: %u)...\n", FWD_V_EMF_ADC_CHANNEL); adc_select_input(FWD_V_EMF_ADC_CHANNEL); adc_run(true); for (uint32_t i = 0; i < n; i++) { offsets_fwd[i] = adc_fifo_get_blocking(); } adc_run(false); adc_fifo_drain(); LOG(1, "Done measuring in forward direction...\n"); // Find overall average discarding outliers in measurement const uint16_t offset_avg_fwd = two_std_dev(offsets_fwd, n); const uint16_t offset_avg_rev = two_std_dev(offsets_rev, n); const uint16_t overall_avg_offset = (offset_avg_fwd + offset_avg_rev) / 2; LOG(1, "New ADC Offset value CV_172 = %u\n", overall_avg_offset); // Create temporary array -> change CV 172 in temp array -> erase flash -> write temp array to flash uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE]; memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP)); CV_ARRAY_TEMP[171] = overall_avg_offset; uintptr_t params_erase[] = {FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE}; int ret_val = flash_safe_execute(call_flash_range_erase, params_erase, FLASH_TIMEOUT_IN_MS); if (ret_val != PICO_OK){ set_error(FLASH_SAFE_EXECUTE_ERASE_FAILURE); return; } uintptr_t params_program[] = {FLASH_TARGET_OFFSET, sizeof(CV_ARRAY_TEMP), (uintptr_t)CV_ARRAY_TEMP}; ret_val = flash_safe_execute(call_flash_range_program, params_program, FLASH_TIMEOUT_IN_MS); if(ret_val != PICO_OK){ set_error(FLASH_SAFE_EXECUTE_PROGRAM_FAILURE); return; } } static void acknowledge() { // Acknowledge a CV rd/wr instruction by pulsing the motor in both directions const uint16_t max_lvl = _125M / (CV_ARRAY_FLASH[8] * 100 + 10000); pwm_set_gpio_level(MOTOR_FWD_PIN, max_lvl); busy_wait_ms(3); pwm_set_gpio_level(MOTOR_FWD_PIN, 0); pwm_set_gpio_level(MOTOR_REV_PIN, max_lvl); busy_wait_ms(3); pwm_set_gpio_level(MOTOR_REV_PIN, 0); } static void verify_cv_bit(uint16_t const cv_address, const bool bit_val, uint8_t const bit_pos) { // Check for matching bit, when found call acknowledge() const uint8_t mask = 0b00000001; const bool res = ((CV_ARRAY_FLASH[cv_address] >> bit_pos) & mask) == bit_val; if (res) { acknowledge(); } } static void verify_cv_byte(uint16_t const cv_address, uint8_t const cv_data) { // Check for matching byte, when found call acknowledge() if (CV_ARRAY_FLASH[cv_address] == cv_data) acknowledge(); } static void write_cv_byte(uint16_t cv_address, uint8_t cv_data) { // Write the specified CV byte to flash uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE]; memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP)); CV_ARRAY_TEMP[cv_address] = cv_data; // First erase necessary amount of blocks in flash and then rewrite to flash uintptr_t params_erase[] = {FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE}; int ret_val = flash_safe_execute(call_flash_range_erase, params_erase, FLASH_TIMEOUT_IN_MS); if (ret_val != PICO_OK){ set_error(FLASH_SAFE_EXECUTE_ERASE_FAILURE); return; } uintptr_t params_program[] = { FLASH_TARGET_OFFSET, sizeof(CV_ARRAY_TEMP), (uintptr_t)CV_ARRAY_TEMP}; ret_val = flash_safe_execute(call_flash_range_program, params_program, FLASH_TIMEOUT_IN_MS); if(ret_val != PICO_OK){ set_error(FLASH_SAFE_EXECUTE_PROGRAM_FAILURE); return; } acknowledge(); } static void reset_cv_array_to_default(){ // Reset all CVs to default (CV_ARRAY_DEFAULT) uintptr_t params_erase[] = {FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE}; int ret_val = flash_safe_execute(call_flash_range_erase, params_erase, FLASH_TIMEOUT_IN_MS); if (ret_val != PICO_OK){ set_error(FLASH_SAFE_EXECUTE_ERASE_FAILURE); return; } uintptr_t params_program[] = {FLASH_TARGET_OFFSET, sizeof(CV_ARRAY_DEFAULT), (uintptr_t)CV_ARRAY_DEFAULT}; ret_val = flash_safe_execute(call_flash_range_program, params_program, FLASH_TIMEOUT_IN_MS); if(ret_val != PICO_OK){ set_error(FLASH_SAFE_EXECUTE_PROGRAM_FAILURE); return; } } static void write_cv_handler(uint16_t const cv_index, uint8_t const cv_data) { // There are some exceptions to writing CVs - e.g. writing to a read only CV is not valid - this gets handled here switch (cv_index) { case 0: //CV_1 // CV_1 => Value = 0 is not allowed if (cv_data == 0 || cv_data > 127) { break; } else { write_cv_byte(cv_index, cv_data); } break; case 6: //CV_7 // Read only (CV_7 - Version no.) // ADC offset Adjustment is triggered when setting CV_7 = 7 if (cv_data == 7) { LOG(1, "Triggered ADC offset adjustment via CV_7 = 7\n"); adc_offset_adjustment(ADC_CALIBRATION_ITERATIONS); } break; case 7: //CV_8 // Read only (CV_8 - Manufacturer ID) // Reset all CVs to default (CV_ARRAY_DEFAULT) when setting CV_8 = 8) if (cv_data == 8) { LOG(1, "reset of flash triggered via CV_8 = 8\n"); reset_cv_array_to_default(); } break; case 16: // CV_17 // CV_17 must have a value between 11000000->(192dec) and 11100111->(231dec) inclusive // CV_17 == 192 && CV_18 == 0 -> Address = 0 is also not valid and therefore shall not be set if ((cv_data < 192 || cv_data > 231) || (CV_ARRAY_FLASH[17] == 0 && cv_data == 192)) { break; } write_cv_byte(cv_index, cv_data); break; case 17: // CV_18 if(CV_ARRAY_FLASH[16] == 192 && cv_data == 0){ break; } write_cv_byte(cv_index, cv_data); break; case 30: // CV_31 & CV_32 Index isn't implemented and shall not be set break; case 31: // CV_31 & CV_32 Index isn't implemented and shall not be set break; default: // Regular CV write is carried out write_cv_byte(cv_index, cv_data); } } static void program_mode(size_t const number_of_bytes, const uint8_t *const byte_array) { //First check for valid programming command ("address" 112-127) if (byte_array[number_of_bytes - 1] < 128 && byte_array[number_of_bytes - 1] > 111) { const uint8_t instruction_type_mask = 0b00001100; const uint8_t instruction_type = instruction_type_mask & byte_array[number_of_bytes - 1]; const uint8_t cv_address_ms_bits_mask = 0b00000011; const uint16_t cv_address_ms_bits = cv_address_ms_bits_mask & byte_array[number_of_bytes - 1]; const uint16_t cv_address = byte_array[number_of_bytes - 2] + (cv_address_ms_bits << 8); if (instruction_type == 0b000001000) { // Verify CV bit instruction const uint8_t bit_pos_mask = 0b00000111; const uint8_t bit_pos = bit_pos_mask & byte_array[number_of_bytes - 3]; const uint8_t bit_val_mask = 0b00000001; const uint8_t bit_val_uint = (byte_array[number_of_bytes - 3] >> 3) & bit_val_mask; const bool bit_val = bit_val_uint; verify_cv_bit(cv_address, bit_val, bit_pos); } else if (instruction_type == 0b000000100) { // Verify CV byte instruction const uint8_t cv_data = byte_array[number_of_bytes - 3]; verify_cv_byte(cv_address, cv_data); } else if (instruction_type == 0b000001100) { // Write CV byte instruction const uint8_t cv_data = byte_array[number_of_bytes - 3]; write_cv_handler(cv_address, cv_data); } busy_wait_ms(5); } } static void set_outputs(uint32_t const functions_to_set_bitmask) { // Get outputs with pwm enabled and preset outputs_to_set_PWM variable with resulting GPIO Bitmask const uint32_t PWM_enabled_outputs = get_32bit_CV(111); uint32_t outputs_to_set_PWM = PWM_enabled_outputs; // Get enabled output configuration corresponding to set functions and direction uint32_t outputs_to_set = 0; uint32_t temp_mask = 1; for (uint8_t i = 0; i < 32; i++) { if (temp_mask & functions_to_set_bitmask) { const direction_t dir = get_direction_of_speed_step(speed_step_target); outputs_to_set |= get_32bit_CV(i * 8 + 260 - 4 * dir); } temp_mask <<= 1; } outputs_to_set_PWM &= outputs_to_set; // Outputs with PWM to be enabled outputs_to_set &= ~outputs_to_set_PWM; // Outputs without PWM to be enabled // Set regular outputs without PWM, preventing illegal GPIO by masking with GPIO_ALLOWED_OUTPUTS gpio_put_masked(GPIO_ALLOWED_OUTPUTS, outputs_to_set); // Set PWM enabled outputs to desired level temp_mask = 1; for (uint8_t i = 0; i < 32; ++i) { if (temp_mask & outputs_to_set_PWM) { pwm_set_gpio_level(i, level_table[i]); pwm_gpio_to_channel(i); pwm_gpio_to_slice_num(i); } else if (temp_mask & PWM_enabled_outputs) { pwm_set_gpio_level(i, 0); } temp_mask <<= 1; } } static void update_active_functions(uint32_t new_function_bitmask, const uint8_t clr_bit_ind, bool const direction_change) { // Update functions F0 - F31 when function command is received or in case of direction change static uint32_t active_functions; static uint32_t prev_active_func; // Outputs depend on direction, therefore on direction change outputs need to be set for the other direction. if (direction_change) { // In case of a direction change every output needs to be set according to configuration for the other direction set_outputs(active_functions); } else { // In case of a change in active functions only the function group corresponding to the instruction is considered for updating the outputs // First, check for changes new_function_bitmask &= ~(clr_bit_arr[clr_bit_ind]); // Clear every bit except bits corresponding to group of functions active_functions &= clr_bit_arr[clr_bit_ind]; // Clear bits corresponding to group of functions active_functions |= new_function_bitmask; // Write bits corresponding to group of functions const uint32_t changes = active_functions ^ prev_active_func; // Checks for changes from previous state // When there is changes, set outputs accordingly if (changes) { set_outputs(active_functions); } // Update previously active function variable prev_active_func = active_functions; } } static bool error_detection(size_t const number_of_bytes, const uint8_t *const byte_array) { // Bitwise XOR for all Bytes -> when result is: "0b00000000" error check is passed. uint8_t xor_byte = 0; for (int i = 0; i < number_of_bytes; i++) { xor_byte = xor_byte ^ byte_array[i]; } return (0 == xor_byte); } static bool is_long_address(size_t const number_of_bytes, const uint8_t *const byte_array) { // Check for long address. Function returns true for long address, false for short address. if ((byte_array[number_of_bytes - 1] >> 6) == 0b00000011) { return true; } return false; } static bool address_evaluation(size_t const number_of_bytes, const uint8_t *const byte_array) { // First checks for idle message and then evaluates address included in byte_array[] which contains the received DCC message // Check for idle message if (byte_array[number_of_bytes - 1] == 255) { return false; } // Long/extended address decoder configuration (CV_29 Bit5) const bool CV_29_bit5 = (CV_ARRAY_FLASH[28] & 0b00100000) >> 5; uint16_t read_address; // Check if decoder is configured to receive long/extended address (CV_29 Bit5 set) if (CV_29_bit5) { // Check DCC message for long address format if (is_long_address(number_of_bytes, byte_array)) { // DCC message received has long address format // start of transmission -> address_byte_1 -> address_byte_0 -> ... -> end of transmission const uint16_t address_byte_1 = (byte_array[number_of_bytes - 1]) - 192; // Remove long address identifier bits const uint16_t address_byte_0 = (byte_array[number_of_bytes - 2]); read_address = (address_byte_1 << 8) + address_byte_0; const uint16_t long_address = get_16bit_CV(16) & 0x3FFF; // &Mask to remove long address identifier bits return (long_address == read_address); } else { // DCC message received does not have long address format return false; } } else { // Else decoder is configured to receive short address (CV_29 Bit5 not set) // Short address message: // start of transmission -> address_byte_0 -> ... -> end of transmission read_address = byte_array[number_of_bytes - 1]; return CV_ARRAY_FLASH[0] == read_address; } } static void instruction_evaluation(size_t const number_of_bytes, const uint8_t *const byte_array) { // Evaluate the type of instruction // start of transmission -> ... -> command_byte_n -> ... -> command_byte_0 -> ... -> end of transmission // The position of command bytes depend on whether the address is long or not uint8_t command_byte_start_index; if (is_long_address(number_of_bytes, byte_array)) { command_byte_start_index = number_of_bytes - 3; } else { command_byte_start_index = number_of_bytes - 2; } const uint8_t command_byte_n = byte_array[command_byte_start_index]; if (command_byte_n == 0b00111111) { // 0011-1111 (128 Speed Step Control) - 2 Byte length speed_step_target_prev = speed_step_target; speed_step_target = byte_array[command_byte_start_index - 1]; // Check for direction change const bool direction_changed = get_direction_of_speed_step(speed_step_target) != get_direction_of_speed_step(speed_step_target_prev); // In case of a direction change, functions need to be updated because functions depend on direction if (direction_changed) { update_active_functions(0, 0, true); } } else if (command_byte_n >> 6 == 0b00000010) { // 10XX-XXXX (Function Group Instruction) switch (command_byte_n >> 4) { case 0b00001011: // F5-F8 update_active_functions((command_byte_n << 5), 1, false); break; case 0b00001010: // F9-F12 update_active_functions((command_byte_n << 9), 2, false); break; default: // F0-F4 update_active_functions((((command_byte_n & 0b00001111) << 1) + ((command_byte_n & 0b00010000) >> 4)), 0, false); break; } } else if (command_byte_n >> 5 == 0b00000110) { // Feature Expansion Instruction 110X-XXXX switch (command_byte_n) { case 0b11011110: // F13-F20 update_active_functions((byte_array[command_byte_start_index - 1] << 13), 3, false); break; case 0b11011111: // F21-F28 update_active_functions((byte_array[command_byte_start_index - 1] << 21), 4, false); break; case 0b11011000: // F29-F31 update_active_functions((byte_array[command_byte_start_index - 1] << 29), 5, false); break; default: break; } } } static bool reset_message_check(size_t const number_of_bytes, const uint8_t *const byte_array) { // Check for reset message - When reset message is found, stop the motor and disable all functions. if (byte_array[number_of_bytes - 1] == 0b00000000 && byte_array[number_of_bytes - 2] == 0b00000000) { const direction_t dir = get_direction_of_speed_step(speed_step_target); // Set previous speed step target to current speed step target speed_step_target_prev = speed_step_target; // Set speed step target to emergency stop speed step ( 1 for Reverse direction / 129 for forward direction) // for details see get_direction_of_speed_step() comment in "shared.h" if(dir == DIRECTION_FORWARD) speed_step_target = SPEED_STEP_FORWARD_EMERGENCY_STOP; else if(dir == DIRECTION_REVERSE) speed_step_target = SPEED_STEP_REVERSE_EMERGENCY_STOP; update_active_functions(0,0,0); // Disables all functions return true; } return false; } static size_t detect_dcc_packet() { // Checks for valid package - looking for correct preamble using bitmasks // returns number of bytes if valid bit-pattern is found. Otherwise INVALID_PACKAGE is returned. // INVALID_PACKAGE is defined in core0.h as SIZE_MAX (maximum value of size_t) size_t number_of_bytes = INVALID_PACKAGE; const uint64_t masked_message_3_bytes = input_bit_buffer & MESSAGE_MASK_3_BYTES; if (masked_message_3_bytes == MESSAGE_3_BYTES) number_of_bytes = 3; const uint64_t masked_message_4_bytes = input_bit_buffer & MESSAGE_MASK_4_BYTES; if (masked_message_4_bytes == MESSAGE_4_BYTES) number_of_bytes = 4; const uint64_t masked_message_5_bytes = input_bit_buffer & MESSAGE_MASK_5_BYTES; if (masked_message_5_bytes == MESSAGE_5_BYTES) number_of_bytes = 5; return number_of_bytes; } static void bits_to_dcc_packet_data(dcc_packet_t * packet) { // Writes data in input_bit_buffer to dcc_packet_t struct instance //start of transmission -> byte_n(address byte) -> ... -> byte_0(error detection byte) -> end of transmission for (uint8_t i = 0; i < packet->length; i++) { packet->data[i] = input_bit_buffer >> (i * 9 + 1); } } static void evaluate_packet(dcc_packet_t * packet) { // DCC packet evaluation static bool reset_message_flag; // Check for errors if (error_detection(packet->length, packet->data)) { // Check for matching address if (address_evaluation(packet->length, packet->data)) { reset_message_flag = false; instruction_evaluation(packet->length, packet->data); } else if (reset_message_flag) { // When previous packet was a reset message -> enter program mode program_mode(packet->length, packet->data); } else { // Check for reset message and set flag when reset message is received reset_message_flag = reset_message_check(packet->length, packet->data); } } } static void gpio_irq_cb(uint gpio, uint32_t events) { absolute_time_t start_time = get_absolute_time(); // Check for rising edge on DCC input pin if ((events & GPIO_IRQ_EDGE_RISE) && (gpio == DCC_INPUT_PIN)) { track_signal_rise(gpio, events); } // Check for falling edge on DCC input pin else if ((events & GPIO_IRQ_EDGE_FALL) && (gpio == DCC_INPUT_PIN)) { track_signal_fall(gpio, events); } absolute_time_t end_time = get_absolute_time(); if (absolute_time_diff_us(start_time, end_time) > 20) { LOG(1, "Time gpio_irq_cb: %lld us\n", absolute_time_diff_us(start_time, end_time)); } } static void track_signal_rise() { // DCC-Signal pin rising edge. Write current time to rising_edge_time rising_edge_time = get_absolute_time(); } static void track_signal_fall() { // DCC-Signal pin falling edge. Write current time to falling_edge_time falling_edge_time = get_absolute_time(); // Time difference is equal to the time the signal was in a logical high state const int64_t time_logical_high = absolute_time_diff_us(rising_edge_time, falling_edge_time); // When logical high was longer than 87us write 0 bit into buffer otherwise 1 bool bit; if (time_logical_high > 87) bit = 0; else bit = 1; input_bit_buffer <<= 1; input_bit_buffer |= bit; // Check if input buffer contains a valid dcc packet // number_of_bytes contains the length of the packet when detected, otherwise -1 dcc_r_buf.packets[dcc_r_buf.wr_idx].length = detect_dcc_packet(); if (dcc_r_buf.packets[dcc_r_buf.wr_idx].length != INVALID_PACKAGE) { // Write data into ring buffer containing dcc_packet_t struct instances bits_to_dcc_packet_data(&dcc_r_buf.packets[dcc_r_buf.wr_idx]); // Increment write index of ring buffer increment_ring_buffer_idx(&dcc_r_buf.wr_idx, RING_BUFFER_PACKETS); } } static void init_outputs() { LOG(1, "Initializing Outputs...\n"); gpio_init_mask(GPIO_ALLOWED_OUTPUTS); gpio_set_dir_out_masked(GPIO_ALLOWED_OUTPUTS); // Note: This might also disable UART on GPIO0 & GPIO1 const uint32_t PWM_enabled_outputs = get_32bit_CV(111) & GPIO_ALLOWED_OUTPUTS; uint32_t mask = 1; for (uint8_t i = 0; i < sizeof(uint32_t)*8; ++i) { if (PWM_enabled_outputs & mask) { const uint32_t slice = pwm_gpio_to_slice_num(i); const uint32_t channel = pwm_gpio_to_channel(i); // Channel A = "0"; Channel B = "1" const uint16_t wrap = get_16bit_CV(115 + 7 * slice); const uint16_t level = get_16bit_CV(118 + 7 * slice + 2 * channel); const uint8_t clock_divider = CV_ARRAY_FLASH[117 + 7 * slice] + 1; gpio_set_function(i, GPIO_FUNC_PWM); pwm_set_wrap(slice, wrap); pwm_set_gpio_level(i, 0); level_table[i] = level; pwm_set_clkdiv_int_frac(slice, clock_divider, 0); pwm_set_enabled(slice, true); LOG(1, "Set GPIO pin: %u as PWM output; PWM slice: %u; PWM channel: %u; Duty cycle: %f; Clock divider: %u\n", i, slice, channel, (float) level/wrap, clock_divider); } mask <<= 1; } } static void cv_setup_check() { LOG(1, "Checking CV array for factory state of flash or missing ADC offset setup...\n"); // Check for flash factory setting and set CV_FLASH_ARRAY to default values when factory condition ("0xFF") is found. if (CV_ARRAY_FLASH[64] == 0xFF) { LOG(1, "Detected flash memory factory condidition (CV_65 == %u), resetting all CVs to default values...\n", CV_ARRAY_FLASH[64]); reset_cv_array_to_default(); } // Check for existing ADC offset setup if (CV_ARRAY_FLASH[171] == 0xFF) { LOG(1, "Detected ADC offset factory condidition (CV_172 == %u), running offset adjustment measurement function...\n", CV_ARRAY_FLASH[171]); adc_offset_adjustment(ADC_CALIBRATION_ITERATIONS); } LOG(1, "CV check done! Setting wait_for_cv_setup_check flag to false!\n"); cv_setup_check_done = true; } static void init_motor_pwm(uint8_t const gpio) { // Motor PWM initialization LOG(2, "Initializing Motor PWM on GPIO pin: %u...\n", gpio); // Set GPIO pin to PWM functionality gpio_set_function(gpio, GPIO_FUNC_PWM); // Set wrap counter value saved in CV const uint16_t wrap_counter = (_125M / (CV_ARRAY_FLASH[8] * 100 + 10000)) - 1; const uint32_t slice_num = pwm_gpio_to_slice_num(gpio); pwm_set_clkdiv_int_frac(slice_num, CV_ARRAY_FLASH[173], 0); pwm_set_wrap(slice_num, wrap_counter); // Set initial level to 0 pwm_set_gpio_level(gpio, 0); // Enable PWM pwm_set_enabled(slice_num, true); LOG(2, "Initialized motor PWM on pin: %u; wrap_counter %u; clkdiv %d;\n", gpio, wrap_counter, CV_ARRAY_FLASH[173]); } static void init_adc() { LOG(1, "Initializing ADC...\n") // Initialize ADC adc_init(); // Set ADC GPIO pins to ADC functionality adc_gpio_init(FWD_V_EMF_ADC_PIN); adc_gpio_init(REV_V_EMF_ADC_PIN); // Configure ADC FIFO adc_fifo_setup(true, false, 0, false, false); LOG(1, "ADC initialization done!\n") } static void init_digital_input() { LOG(1, "Initializing DCC input pin...\n"); gpio_init(DCC_INPUT_PIN); gpio_set_dir(DCC_INPUT_PIN, GPIO_IN); gpio_pull_up(DCC_INPUT_PIN); LOG(1, "DCC input pin initialization done!\n"); } static void wait_for_stdio_input() { while (true) { //watchdog_update(); // Send a message to the user asking them to acknowledge it by sending a reply LOG(1, "Send any character to continue.\n"); // Wait for a character int received_char = getchar_timeout_us(1e6); if ((received_char != PICO_ERROR_TIMEOUT) && (received_char > 0)) { // If a character is received, exit the function LOG(1, "Character '%c' received. Continuing...\n", (char)received_char); return; } // If no character is received, retry... } } int main() { exception_set_exclusive_handler(HARDFAULT_EXCEPTION, hardfault_handler); #ifdef RP2040_DECODER_DEFAULT_LED_PIN // Initialize LED GPIO pin gpio_init(RP2040_DECODER_DEFAULT_LED_PIN); gpio_set_dir(RP2040_DECODER_DEFAULT_LED_PIN, GPIO_OUT); // Blink LED once for 200ms to indicate startup gpio_put(RP2040_DECODER_DEFAULT_LED_PIN, 1); busy_wait_ms(200); gpio_put(RP2040_DECODER_DEFAULT_LED_PIN, 0); busy_wait_ms(200); #endif // Initialize stdio when enabled #if (STDIO_UART_ENABLED || STDIO_USB_ENABLED) if(stdio_init_all() != true){ set_error(STDIO_INIT_FAILURE); } // When LOG_WAIT == 1 and LOGLEVEL > 0 wait for user input before continuing. User input can be any character. #if (LOGLEVEL > 0 && LOG_WAIT == 1) wait_for_stdio_input(); printf("%u", STDIO_UART_ENABLED); #endif #endif LOG(1, "core0 Initialization...\n"); // Check for reboot by watchdog and set error when true if (watchdog_caused_reboot()) { LOG(1, "Reboot by watchdog detected!\n"); set_error(REBOOT_BY_WATCHDOG); } // Initialize Motor PWM pins init_motor_pwm(MOTOR_FWD_PIN); init_motor_pwm(MOTOR_REV_PIN); // Initialize outputs init_outputs(); // Initialize ADC init_adc(); // Initialize digital inputs and track signal irq init_digital_input(); LOG(1, "core0 initialization done!\n"); // Launch core1 multicore_launch_core1(core1_entry); // Wait for core1 to call flash_safe_execute_core_init() and set the flash_safe_execute_core_init_done flag LOG(1, "Waiting for flash_safe_execute_core_init_done flag...\n"); while (!flash_safe_execute_core_init_done) { watchdog_update(); } busy_wait_ms(100); // Check for error calling flash_safe_execute_core_init() on core1 if(get_error_state() & FLASH_SAFE_EXECUTE_CORE_INIT_FAILURE){ panic("Error calling flash_safe_execute_core_init() on core1!"); //TODO: test } // Check CV array for factory state of flash or missing ADC offset setup cv_setup_check(); // Register GPIO IRQ callback gpio_set_irq_callback(gpio_irq_cb); // Enable IRQ gpio_set_irq_enabled(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE | GPIO_IRQ_EDGE_FALL, true); irq_set_enabled(IO_IRQ_BANK0, true); // Enable the watchdog, requiring the watchdog to be updated every WATCHDOG_TIMER_IN_MS milliseconds or the chip will reboot // second arg is pause on debug which means the watchdog will pause when stepping through code // Watchdog is updated by core0 and core1 whenever there is time and hopefully soon enough to prevent a reboot. watchdog_enable(WATCHDOG_TIMER_IN_MS, 1); // Endless loop while (true) { // Check for new messages in ring buffer if (dcc_r_buf.wr_idx != dcc_r_buf.rd_idx) { absolute_time_t start_time = get_absolute_time(); evaluate_packet(&dcc_r_buf.packets[dcc_r_buf.rd_idx]); increment_ring_buffer_idx(&dcc_r_buf.rd_idx, RING_BUFFER_PACKETS); absolute_time_t end_time = get_absolute_time(); if (absolute_time_diff_us(start_time, end_time) > 40) { LOG(1, "Time to evaluate message: %lld us\n", absolute_time_diff_us(start_time, end_time)); } } else { watchdog_update(); } } }