////////////////////////// // RP2040-Decoder // // Gabriel Koppenstein // // core0.c // ////////////////////////// #include "core0.h" bool target_direction = true; //Forward = true - Reverse = false uint target_speed_step = 128; //128 = Stop (Forward Direction) const uint8_t *CV_ARRAY_FLASH = (const uint8_t *) (XIP_BASE + FLASH_TARGET_OFFSET); uint64_t last_bits = 0; bool reset_package_flag = false; absolute_time_t falling_edge_time,rising_edge_time; uint16_t level_table[32] = {0}; uint16_t two_sigma(const uint16_t arr[], uint8_t length){ //Calculate arithmetic average uint32_t sum = 0; for (uint i = 0; i < length; ++i) { sum += arr[i]; } uint16_t x_avg = sum / length; //Calculate variance sum = 0; for (uint8_t i = 0; i < length; ++i) { sum += (arr[i]-x_avg)*(arr[i]-x_avg); } float variance = (float) sum/ (float)(length-1); //Calculate standard deviation uint16_t std_dev = (uint16_t)sqrtf(variance); //"Filter" every array element that deviates more than 2*(std_dev) sum = 0; uint8_t counter = 0; for (uint8_t i = 0; i < length; ++i) { uint16_t val = arr[i]-x_avg; if ( val < 2*std_dev || val > (0-2*std_dev) ){ sum += arr[i]; counter++; } } //Calculate and return "new" arithmetic average from "filtered" array return sum / counter; } void adc_offset_adjustment(uint8_t length){ uint16_t offsets[length]; //Set PWM level to 0 just for good measure pwm_set_gpio_level(MOTOR_FWD_PIN, 0); pwm_set_gpio_level(MOTOR_REV_PIN, 0); for (uint8_t i = 0; i < length; i++) { uint16_t fwd = measure(true); uint16_t rev = measure(false); offsets[i] = (fwd+rev)/2; } uint8_t offsets_fwd_avg = two_sigma(offsets, length); uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE]; memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP)); CV_ARRAY_TEMP[171] = offsets_fwd_avg; flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE); flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2); } void acknowledge() { uint16_t max_lvl = _125M/(CV_ARRAY_FLASH[8]*100+10000); pwm_set_gpio_level(MOTOR_FWD_PIN, max_lvl); busy_wait_ms(3); pwm_set_gpio_level(MOTOR_FWD_PIN, 0); pwm_set_gpio_level(MOTOR_REV_PIN, max_lvl); busy_wait_ms(3); pwm_set_gpio_level(MOTOR_REV_PIN, 0); } void verify_cv_bit(uint16_t cv_address,bool bit_val, uint8_t bit_pos) { uint8_t mask = 0b00000001; bool res = ( (CV_ARRAY_FLASH[cv_address] >> bit_pos) &mask ) == bit_val; if (res) { acknowledge(); } } void verify_cv_byte(uint16_t cv_address, uint8_t cv_data){ if (CV_ARRAY_FLASH[cv_address] == cv_data) acknowledge(); } void write_cv_byte(uint16_t cv_index, uint8_t cv_data){ //CV_7 & CV_8 are read-only //Reset all CVs to Default (CV_8; Value = 8) if(cv_index == 7 && cv_data == 8){ flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE); flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_DEFAULT, FLASH_PAGE_SIZE * 2); } //ADC offset Adjustment (CV_7; Value = 7); else if(cv_index == 6 && cv_data == 7){ adc_offset_adjustment(CV_ARRAY_FLASH[173]); } else if( !cv_index && !cv_data ); else{ uint8_t CV_ARRAY_TEMP[CV_ARRAY_SIZE]; memcpy(CV_ARRAY_TEMP, CV_ARRAY_FLASH, sizeof(CV_ARRAY_TEMP)); CV_ARRAY_TEMP[cv_index] = cv_data; flash_range_erase(FLASH_TARGET_OFFSET, FLASH_SECTOR_SIZE); flash_range_program(FLASH_TARGET_OFFSET, CV_ARRAY_TEMP, FLASH_PAGE_SIZE * 2); acknowledge(); } } void program_mode(uint8_t number_of_bytes, const uint8_t byte_array[]){ //Check for valid programming command ("address" 112-127) if (byte_array[number_of_bytes - 1]<128 && byte_array[number_of_bytes - 1]>111){ uint8_t instruction_type_mask = 0b00001100; uint8_t instruction_type = instruction_type_mask & byte_array[number_of_bytes - 1]; uint8_t cv_address_ms_bits_mask = 0b00000011; uint16_t cv_address_ms_bits = cv_address_ms_bits_mask & byte_array[number_of_bytes - 1]; uint16_t cv_address = byte_array[number_of_bytes - 2] + (cv_address_ms_bits << 8); if(pid_control_timer.pool)alarm_pool_destroy(pid_control_timer.pool); if(speed_helper_timer.pool)alarm_pool_destroy(speed_helper_timer.pool); multicore_reset_core1(); uint32_t saved_interrupts = save_and_disable_interrupts(); if (instruction_type == 0b000001000) { uint8_t bit_pos_mask = 0b00000111; uint8_t bit_pos = bit_pos_mask&byte_array[number_of_bytes - 3]; uint8_t bit_val_mask = 0b00000001; uint8_t bit_val_uint = (byte_array[number_of_bytes - 3]>>3) & bit_val_mask; bool bit_val = bit_val_uint; verify_cv_bit(cv_address, bit_val, bit_pos); } else if (instruction_type == 0b000000100) { uint8_t cv_data = byte_array[number_of_bytes - 3]; verify_cv_byte(cv_address, cv_data); } else if (instruction_type == 0b000001100) { uint8_t cv_data = byte_array[number_of_bytes - 3]; write_cv_byte(cv_address, cv_data); } restore_interrupts(saved_interrupts); multicore_launch_core1(core1_entry); multicore_fifo_pop_blocking(); //wait for core1 launch before proceeding } } uint32_t get_32bit_CV (uint16_t CV_start_index){ uint8_t byte_0 = CV_ARRAY_FLASH[CV_start_index]; uint8_t byte_1 = CV_ARRAY_FLASH[CV_start_index+1]; uint8_t byte_2 = CV_ARRAY_FLASH[CV_start_index+2]; uint8_t byte_3 = CV_ARRAY_FLASH[CV_start_index+3]; return (byte_0) + (byte_1<<8) + (byte_2<<16) + (byte_3<<24); } uint16_t get_16bit_CV (uint16_t CV_start_index){ uint8_t byte_0 = CV_ARRAY_FLASH[CV_start_index]; uint8_t byte_1 = CV_ARRAY_FLASH[CV_start_index+1]; return (byte_0) + (byte_1<<8); } void set_outputs(uint32_t functions_to_set_bitmask) { uint32_t outputs_to_set = 0; uint32_t outputs_with_PWM_enabled = get_32bit_CV(111); //get outputs with pwm enabled (bitmask) uint32_t outputs_to_set_PWM = outputs_with_PWM_enabled; uint32_t temp_mask = 1; for (uint8_t i = 0; i < 32; i++) { if (temp_mask & functions_to_set_bitmask ){ outputs_to_set |= get_32bit_CV(i * 8 + 260 - 4 * target_direction); } temp_mask<<=1; } outputs_to_set &= GPIO_ALLOWED_OUTPUTS; // Prevent illegal GPIO outputs_to_set_PWM &= outputs_to_set; // Outputs with PWM to be enabled outputs_to_set &= ~outputs_to_set_PWM; // Outputs without PWM to be enabled gpio_put_masked(GPIO_ALLOWED_OUTPUTS, outputs_to_set); temp_mask = 1; for (uint8_t i = 0; i < 32; ++i) { if(temp_mask & outputs_to_set_PWM){ pwm_set_gpio_level(i, level_table[i]); pwm_gpio_to_channel(i); pwm_gpio_to_slice_num(i); } else if (temp_mask & outputs_with_PWM_enabled){ pwm_set_gpio_level(i,0); } temp_mask<<=1; } } void update_active_functions(uint32_t new_function_bitmask, uint8_t clr_bit_ind, bool direction_change) { static uint32_t active_functions; static uint32_t prev_active_func; if (direction_change){ set_outputs(prev_active_func); } else{ new_function_bitmask &= ~(clr_bit_arr[clr_bit_ind]); //clear every bit except bits corresponding to group of functions active_functions &= clr_bit_arr[clr_bit_ind]; //clear bits corresponding to group of functions active_functions |= new_function_bitmask; //write bits corresponding to group of functions uint32_t changes = active_functions ^ prev_active_func; //xor effectively checks for changes from previous state if(changes)set_outputs(active_functions); prev_active_func = active_functions; } } bool error_detection(int8_t number_of_bytes, const uint8_t byte_array[]) { //Bitwise XOR for all Bytes -> Successful result is: "0000 0000" uint8_t xor_byte = 0; for (int i = 0; i < number_of_bytes; i++) { xor_byte = xor_byte ^ byte_array[i]; } return (0 == xor_byte); } // Returns true for long address bool is_long_address(uint8_t number_of_bytes, const uint8_t byte_array[]) { if ((byte_array[number_of_bytes - 1]>>6) == 0b00000011) return true; return false; } bool address_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[]) { //Check for Idle Package if (byte_array[number_of_bytes - 1] == 255) { return false; } uint16_t read_address; //Long Address Package if (is_long_address(number_of_bytes, byte_array)) { //start of transmission -> address_byte_1 -> address_byte_0 -> ... -> end of transmission uint16_t address_byte_1 = (byte_array[number_of_bytes - 1]) - 192; //remove long address identifier bits uint16_t address_byte_0 = (byte_array[number_of_bytes - 2]); read_address = (address_byte_1 << 8) + address_byte_0; uint8_t long_address_mask = 0b00111111; uint16_t long_address = ((CV_ARRAY_FLASH[16]&long_address_mask)<<8)+CV_ARRAY_FLASH[17]; return(long_address==read_address); } //Short Address Package else { //start of transmission -> address_byte_0 -> ... -> end of transmission read_address = (byte_array[number_of_bytes - 1]); return (CV_ARRAY_FLASH[0] == read_address); } } void instruction_evaluation(uint8_t number_of_bytes,const uint8_t byte_array[]) { uint8_t command_byte_n; uint8_t command_byte_start_index; // start of transmission -> ... -> command_byte_n -> ... -> command_byte_0 -> ... -> end of transmission if (is_long_address(number_of_bytes,byte_array)) { command_byte_start_index = number_of_bytes - 3; } else { command_byte_start_index = number_of_bytes - 2; } command_byte_n = byte_array[command_byte_start_index]; //0011-1111 (128 Speed Step Control) - 2 Byte length if (command_byte_n == 0b00111111){ target_speed_step = byte_array[command_byte_start_index - 1]; if(target_speed_step>127 && !target_direction) { target_direction = true; //Change direction variable to forward (true) update_active_functions(0,0,1); //Some functions depend on direction } else if (target_speed_step<128 && target_direction){ target_direction = false; //Change direction variable to reverse (false) update_active_functions(0,0,1); //Some functions depend on direction } } // 10XX-XXXX (Function Group Instruction) else if (command_byte_n >> 6 == 0b00000010){ switch (command_byte_n >> 4) { case 0b00001011: // F5-F8 update_active_functions((command_byte_n << 5),1,false); break; case 0b00001010: // F9-F12 update_active_functions((command_byte_n << 9),2,false); break; default: // F0-F4 update_active_functions(((command_byte_n << 1) + (command_byte_n >> 4)),0,false); break; } } //Feature Expansion Instruction 110X-XXXX else if (command_byte_n >> 5 == 0b00000110) { switch (command_byte_n) { case 0b11011110: // F13-F20 update_active_functions((byte_array[command_byte_start_index - 1] << 13),3,false); break; case 0b11011111: // F21-F28 update_active_functions((byte_array[command_byte_start_index - 1] << 21),4,false); break; case 0b11011000: // F29-F31 update_active_functions((byte_array[command_byte_start_index - 1] << 29),5,false); break; default: break; } } } bool reset_package_check(uint8_t number_of_bytes,const uint8_t byte_array[]){ if (byte_array[number_of_bytes-1] == 0b00000000 && byte_array[number_of_bytes-2] == 0b00000000){ target_speed_step = 1; //update_active_functions(0,0,37); return true; } else { return false; } } int8_t check_for_package() { //returns number of bytes if valid bit-pattern is found. Otherwise -1 is returned. uint64_t package3Masked = last_bits & PACKAGE_MASK_3_BYTES; if (package3Masked == PACKAGE_3_BYTES) { return 3; } uint64_t package4Masked = last_bits & PACKAGE_MASK_4_BYTES; if (package4Masked == PACKAGE_4_BYTES) { return 4; } uint64_t package5Masked = last_bits & PACKAGE_MASK_5_BYTES; if (package5Masked == PACKAGE_5_BYTES) { return 5; } return -1; } void writeLastBit(bool bit) { last_bits <<= 1; last_bits |= bit; } //start of transmission -> byte_n(address byte) -> ... -> byte_0(error detection byte) -> end of transmission void bits_to_byte_array(int8_t number_of_bytes,uint8_t byte_array[]) { for (uint8_t i = 0; i < number_of_bytes; i++) { byte_array[i] = last_bits >> (i * 9 + 1); } } void evaluation(){ int8_t number_of_bytes = check_for_package(); if (number_of_bytes != -1) { uint8_t byte_array[SIZE_BYTE_ARRAY] = {0}; bits_to_byte_array(number_of_bytes,byte_array); if(byte_array[number_of_bytes-3]==239 && byte_array[number_of_bytes-4]==151){ } if (error_detection(number_of_bytes,byte_array)) { if (address_evaluation(number_of_bytes,byte_array)) { reset_package_flag = false; instruction_evaluation(number_of_bytes,byte_array); } else if (reset_package_flag) { program_mode(number_of_bytes,byte_array); } else { reset_package_flag = reset_package_check(number_of_bytes,byte_array); } } } } void track_signal_rise(unsigned int gpio, long unsigned int events) { rising_edge_time = get_absolute_time(); gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, false, &track_signal_rise); gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, true, &track_signal_fall); } void track_signal_fall(unsigned int gpio, long unsigned int events) { falling_edge_time = get_absolute_time(); int64_t time_logical_high = absolute_time_diff_us(rising_edge_time,falling_edge_time); if(time_logical_high > 87) { writeLastBit(0); } else { writeLastBit(1); } evaluation(); gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_FALL, false, &track_signal_fall); gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise); } void init_outputs(){ gpio_init_mask(GPIO_ALLOWED_OUTPUTS); gpio_set_dir_out_masked(GPIO_ALLOWED_OUTPUTS); //note: This also disables UART on GPIO0 & GPIO1 uint32_t Outputs_with_PWM_enabled = get_32bit_CV(111); uint32_t slice, channel; uint16_t wrap, level; uint32_t temp_mask = 1; for (uint8_t i = 0; i < 32; ++i) { if (Outputs_with_PWM_enabled&temp_mask){ slice = pwm_gpio_to_slice_num(i); channel = pwm_gpio_to_channel(i); //0 for Channel A, 1 for Channel B wrap = get_16bit_CV(115 + slice*7); level = get_16bit_CV(118 + 7*slice+ 2*channel); gpio_set_function(i,GPIO_FUNC_PWM); pwm_set_wrap(slice,wrap); pwm_set_gpio_level(i,0); level_table[i] = level; pwm_set_clkdiv_int_frac(slice,CV_ARRAY_FLASH[117+7*slice],0); pwm_set_enabled(slice,true); } temp_mask<<=1; } } void cv_setup_check(){ //Check for flash factory setting and set CV_FLASH_ARRAY to default values when factory condition is found. multicore_fifo_pop_blocking(); //wait for core1 launch before proceeding if (CV_ARRAY_FLASH[64]){ uint8_t arr[4] = {125,8,7,124}; program_mode(4,arr); //reset to CV_ARRAY_DEFAULT (write CV_8 = 8) } //Check for adc offset setup if ( CV_ARRAY_FLASH[171] == 0xFF ){ uint8_t arr[4] = {125,7,6,124}; program_mode(4,arr); //ADC offset adjustment (write CV_7 = 7) } } int main() { stdio_init_all(); printf("core0 init...\n"); multicore_launch_core1(core1_entry); cv_setup_check(); init_outputs(); gpio_init(DCC_INPUT_PIN); gpio_set_dir(DCC_INPUT_PIN, GPIO_IN); gpio_pull_up(DCC_INPUT_PIN); gpio_set_irq_enabled_with_callback(DCC_INPUT_PIN, GPIO_IRQ_EDGE_RISE, true, &track_signal_rise); printf("core0 done\n"); while (1); }