/* * Copyright (c) 2020 Raspberry Pi (Trading) Ltd. * * SPDX-License-Identifier: BSD-3-Clause */ // ----------------------------------------------------- // NOTE: THIS HEADER IS ALSO INCLUDED BY ASSEMBLER SO // SHOULD ONLY CONSIST OF PREPROCESSOR DIRECTIVES // ----------------------------------------------------- // Modified version of "boards/pico.h" for using the RP2040-Decoder board // NOTE: THIS IS FOR THE "LEGACY" Version without a USB-C Connector // pico_cmake_set PICO_PLATFORM=rp2040 #ifndef _BOARDS_RP2040_DECODER_H #define _BOARDS_RP2040_DECODER_H // For board detection #define RP2040_DECODER // In case the xosc takes longer to stabilize than usual #ifndef PICO_XOSC_STARTUP_DELAY_MULTIPLIER #define PICO_XOSC_STARTUP_DELAY_MULTIPLIER 64 #endif // --- UART --- #ifndef PICO_DEFAULT_UART #define PICO_DEFAULT_UART 0 #endif #ifndef PICO_DEFAULT_UART_TX_PIN #define PICO_DEFAULT_UART_TX_PIN 0 #endif #ifndef PICO_DEFAULT_UART_RX_PIN #define PICO_DEFAULT_UART_RX_PIN 1 #endif // --- FLASH --- // Flash size is 8 MiB for W25Q64JVSSIQ if you decide to use another capacity flash IC change the size to the corresponding value // 8MiB = (8 * 1024 * 1024) bytes = 8388608 bytes #ifndef PICO_FLASH_SIZE_BYTES #define PICO_FLASH_SIZE_BYTES 8388608 #endif // Offset from base address used for saving CV_ARRAY_FLASH - in this case one sector size from the end of flash #define FLASH_TARGET_OFFSET (PICO_FLASH_SIZE_BYTES-FLASH_SECTOR_SIZE) // For some reason the clock divider of 4 is necessary, otherwise the controller occasionally hard faults // Another workaround could be to run code from RAM but this seems to work fine #ifndef PICO_FLASH_SPI_CLKDIV #define PICO_FLASH_SPI_CLKDIV 4 #endif #ifndef PICO_RP2040_B0_SUPPORTED #define PICO_RP2040_B0_SUPPORTED 1 #endif // Other pins // GPIO used for DCC-Signal, Motor PWM or ADC #define DCC_INPUT_PIN 21u #define MOTOR_FWD_PIN 23u #define MOTOR_REV_PIN 22u #define FWD_V_EMF_ADC_PIN 28u #define REV_V_EMF_ADC_PIN 29u #define FWD_V_EMF_ADC_CHANNEL (FWD_V_EMF_ADC_PIN-26u) #define REV_V_EMF_ADC_CHANNEL (REV_V_EMF_ADC_PIN-26u) #if LOGLEVEL != 0 // GPIO used directly (GPIO 2-5 incl.) as outputs or to switch auxiliary output transistors (GPIO 24-27 incl.) #define GPIO_OUTPUT_PIN_MASK ((1u<<24) | (1u<<25) | (1u<<26) | (1u<<27) | (1u<<5) | (1u<<4) | (1u<<3) | (1u<<2)) #else // GPIO used directly (GPIO 0-5 incl.) as outputs or to switch auxiliary output transistors (GPIO 24-27 incl.) #define GPIO_OUTPUT_PIN_MASK ((1u<<24) | (1u<<25) | (1u<<26) | (1u<<27) | (1u<<5) | (1u<<4) | (1u<<3) | (1u<<2) | (1u<<1) | (1u<<0)) #endif // GPIO pin mask to prevent setting illegal GPIOs (ADC, Motor, DCC Input Pin) // When logging to stdio using UART is enabled do NOT use PICO_DEFAULT_UART_TX_PIN and PICO_DEFAULT_UART_RX_PIN as GPIO/PWM outputs #if (LOGLEVEL != 0) && (STDIO_UART_ENABLED != 0) #define GPIO_ILLEGAL_MASK ((1u<