Copy code from flash to ram in order to not use XIP allowing writing to flash memory while both cores are running;

Motor control now operates with two states/modes;
Extended Default CV Range to 1024 - refers to NMRA/RCN standards
This commit is contained in:
gab-k committed 2024-01-05 00:37:21 +01:00
1 parent 577bc5dd5c
commit f3ffb73b62
6 files changed
+738 -199

No files matched your search

+4 -1
View File
@@ -52,5 +52,8 @@ pico_enable_stdio_usb(RP2040-Decoder 0)
# disable uart output (to enable put a 1 instead of the 0) # disable uart output (to enable put a 1 instead of the 0)
pico_enable_stdio_uart(RP2040-Decoder 0) pico_enable_stdio_uart(RP2040-Decoder 0)
# Copy code to from flash to memory, then run from memory
pico_set_binary_type(RP2040-Decoder copy_to_ram)
# create map/bin/hex file etc. # create map/bin/hex file etc.
#pico_add_extra_outputs(RP2040-Decoder) pico_add_extra_outputs(RP2040-Decoder)
+520 -2
View File
@@ -1,9 +1,12 @@
#pragma once #pragma once
#define CV_ARRAY_SIZE 512 #include "pico/stdlib.h"
#define CV_ARRAY_SIZE 1024
// All CVs are 8-bit numbers ranging from (0 - 255)dec = (0b00000000 - 0b11111111)bin = (0x00 - 0xFF)hex // All CVs are 8-bit numbers ranging from (0 - 255)dec = (0b00000000 - 0b11111111)bin = (0x00 - 0xFF)hex
// Note : CV_1 = index 0, CV_2 = index 1, CV_3 = index 2, ... // Note : CV_1 = index 0, CV_2 = index 1, CV_3 = index 2, ...
uint8_t CV_ARRAY_DEFAULT [CV_ARRAY_SIZE] = { // Explicitly write CV_ARRAY_DEFAULT with into flash memory using __in_flash attribute macro
uint8_t __in_flash("Default_CV_values") CV_ARRAY_DEFAULT [CV_ARRAY_SIZE] = {
0b00000011, //CV_1 - Basic address - CV_1 = 0 and CV_1 > 127 are not valid - Default = 3 0b00000011, //CV_1 - Basic address - CV_1 = 0 and CV_1 > 127 are not valid - Default = 3
0b00001000, //CV_2 - V_min - Default = 8 0b00001000, //CV_2 - V_min - Default = 8
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////// /////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
@@ -614,4 +617,519 @@ uint8_t CV_ARRAY_DEFAULT [CV_ARRAY_SIZE] = {
0b00000000, //CV_510 - byte 2 0b00000000, //CV_510 - byte 2
0b00000000, //CV_511 - byte 1 0b00000000, //CV_511 - byte 1
0b00000000, //CV_512 - byte 0 0b00000000, //CV_512 - byte 0
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
0b00000000, //CV_513 -
0b00000000, //CV_514 -
0b00000000, //CV_515 -
0b00000000, //CV_516 -
0b00000000, //CV_517 -
0b00000000, //CV_518 -
0b00000000, //CV_519 -
0b00000000, //CV_520 -
0b00000000, //CV_521 -
0b00000000, //CV_522 -
0b00000000, //CV_523 -
0b00000000, //CV_524 -
0b00000000, //CV_525 -
0b00000000, //CV_526 -
0b00000000, //CV_527 -
0b00000000, //CV_528 -
0b00000000, //CV_529 -
0b00000000, //CV_530 -
0b00000000, //CV_531 -
0b00000000, //CV_532 -
0b00000000, //CV_533 -
0b00000000, //CV_534 -
0b00000000, //CV_535 -
0b00000000, //CV_536 -
0b00000000, //CV_537 -
0b00000000, //CV_538 -
0b00000000, //CV_539 -
0b00000000, //CV_540 -
0b00000000, //CV_541 -
0b00000000, //CV_542 -
0b00000000, //CV_543 -
0b00000000, //CV_544 -
0b00000000, //CV_545 -
0b00000000, //CV_546 -
0b00000000, //CV_547 -
0b00000000, //CV_548 -
0b00000000, //CV_549 -
0b00000000, //CV_550 -
0b00000000, //CV_551 -
0b00000000, //CV_552 -
0b00000000, //CV_553 -
0b00000000, //CV_554 -
0b00000000, //CV_555 -
0b00000000, //CV_556 -
0b00000000, //CV_557 -
0b00000000, //CV_558 -
0b00000000, //CV_559 -
0b00000000, //CV_560 -
0b00000000, //CV_561 -
0b00000000, //CV_562 -
0b00000000, //CV_563 -
0b00000000, //CV_564 -
0b00000000, //CV_565 -
0b00000000, //CV_566 -
0b00000000, //CV_567 -
0b00000000, //CV_568 -
0b00000000, //CV_569 -
0b00000000, //CV_570 -
0b00000000, //CV_571 -
0b00000000, //CV_572 -
0b00000000, //CV_573 -
0b00000000, //CV_574 -
0b00000000, //CV_575 -
0b00000000, //CV_576 -
0b00000000, //CV_577 -
0b00000000, //CV_578 -
0b00000000, //CV_579 -
0b00000000, //CV_580 -
0b00000000, //CV_581 -
0b00000000, //CV_582 -
0b00000000, //CV_583 -
0b00000000, //CV_584 -
0b00000000, //CV_585 -
0b00000000, //CV_586 -
0b00000000, //CV_587 -
0b00000000, //CV_588 -
0b00000000, //CV_589 -
0b00000000, //CV_590 -
0b00000000, //CV_591 -
0b00000000, //CV_592 -
0b00000000, //CV_593 -
0b00000000, //CV_594 -
0b00000000, //CV_595 -
0b00000000, //CV_596 -
0b00000000, //CV_597 -
0b00000000, //CV_598 -
0b00000000, //CV_599 -
0b00000000, //CV_600 -
0b00000000, //CV_601 -
0b00000000, //CV_602 -
0b00000000, //CV_603 -
0b00000000, //CV_604 -
0b00000000, //CV_605 -
0b00000000, //CV_606 -
0b00000000, //CV_607 -
0b00000000, //CV_608 -
0b00000000, //CV_609 -
0b00000000, //CV_610 -
0b00000000, //CV_611 -
0b00000000, //CV_612 -
0b00000000, //CV_613 -
0b00000000, //CV_614 -
0b00000000, //CV_615 -
0b00000000, //CV_616 -
0b00000000, //CV_617 -
0b00000000, //CV_618 -
0b00000000, //CV_619 -
0b00000000, //CV_620 -
0b00000000, //CV_621 -
0b00000000, //CV_622 -
0b00000000, //CV_623 -
0b00000000, //CV_624 -
0b00000000, //CV_625 -
0b00000000, //CV_626 -
0b00000000, //CV_627 -
0b00000000, //CV_628 -
0b00000000, //CV_629 -
0b00000000, //CV_630 -
0b00000000, //CV_631 -
0b00000000, //CV_632 -
0b00000000, //CV_633 -
0b00000000, //CV_634 -
0b00000000, //CV_635 -
0b00000000, //CV_636 -
0b00000000, //CV_637 -
0b00000000, //CV_638 -
0b00000000, //CV_639 -
0b00000000, //CV_640 -
0b00000000, //CV_641 -
0b00000000, //CV_642 -
0b00000000, //CV_643 -
0b00000000, //CV_644 -
0b00000000, //CV_645 -
0b00000000, //CV_646 -
0b00000000, //CV_647 -
0b00000000, //CV_648 -
0b00000000, //CV_649 -
0b00000000, //CV_650 -
0b00000000, //CV_651 -
0b00000000, //CV_652 -
0b00000000, //CV_653 -
0b00000000, //CV_654 -
0b00000000, //CV_655 -
0b00000000, //CV_656 -
0b00000000, //CV_657 -
0b00000000, //CV_658 -
0b00000000, //CV_659 -
0b00000000, //CV_660 -
0b00000000, //CV_661 -
0b00000000, //CV_662 -
0b00000000, //CV_663 -
0b00000000, //CV_664 -
0b00000000, //CV_665 -
0b00000000, //CV_666 -
0b00000000, //CV_667 -
0b00000000, //CV_668 -
0b00000000, //CV_669 -
0b00000000, //CV_670 -
0b00000000, //CV_671 -
0b00000000, //CV_672 -
0b00000000, //CV_673 -
0b00000000, //CV_674 -
0b00000000, //CV_675 -
0b00000000, //CV_676 -
0b00000000, //CV_677 -
0b00000000, //CV_678 -
0b00000000, //CV_679 -
0b00000000, //CV_680 -
0b00000000, //CV_681 -
0b00000000, //CV_682 -
0b00000000, //CV_683 -
0b00000000, //CV_684 -
0b00000000, //CV_685 -
0b00000000, //CV_686 -
0b00000000, //CV_687 -
0b00000000, //CV_688 -
0b00000000, //CV_689 -
0b00000000, //CV_690 -
0b00000000, //CV_691 -
0b00000000, //CV_692 -
0b00000000, //CV_693 -
0b00000000, //CV_694 -
0b00000000, //CV_695 -
0b00000000, //CV_696 -
0b00000000, //CV_697 -
0b00000000, //CV_698 -
0b00000000, //CV_699 -
0b00000000, //CV_700 -
0b00000000, //CV_701 -
0b00000000, //CV_702 -
0b00000000, //CV_703 -
0b00000000, //CV_704 -
0b00000000, //CV_705 -
0b00000000, //CV_706 -
0b00000000, //CV_707 -
0b00000000, //CV_708 -
0b00000000, //CV_709 -
0b00000000, //CV_710 -
0b00000000, //CV_711 -
0b00000000, //CV_712 -
0b00000000, //CV_713 -
0b00000000, //CV_714 -
0b00000000, //CV_715 -
0b00000000, //CV_716 -
0b00000000, //CV_717 -
0b00000000, //CV_718 -
0b00000000, //CV_719 -
0b00000000, //CV_720 -
0b00000000, //CV_721 -
0b00000000, //CV_722 -
0b00000000, //CV_723 -
0b00000000, //CV_724 -
0b00000000, //CV_725 -
0b00000000, //CV_726 -
0b00000000, //CV_727 -
0b00000000, //CV_728 -
0b00000000, //CV_729 -
0b00000000, //CV_730 -
0b00000000, //CV_731 -
0b00000000, //CV_732 -
0b00000000, //CV_733 -
0b00000000, //CV_734 -
0b00000000, //CV_735 -
0b00000000, //CV_736 -
0b00000000, //CV_737 -
0b00000000, //CV_738 -
0b00000000, //CV_739 -
0b00000000, //CV_740 -
0b00000000, //CV_741 -
0b00000000, //CV_742 -
0b00000000, //CV_743 -
0b00000000, //CV_744 -
0b00000000, //CV_745 -
0b00000000, //CV_746 -
0b00000000, //CV_747 -
0b00000000, //CV_748 -
0b00000000, //CV_749 -
0b00000000, //CV_750 -
0b00000000, //CV_751 -
0b00000000, //CV_752 -
0b00000000, //CV_753 -
0b00000000, //CV_754 -
0b00000000, //CV_755 -
0b00000000, //CV_756 -
0b00000000, //CV_757 -
0b00000000, //CV_758 -
0b00000000, //CV_759 -
0b00000000, //CV_760 -
0b00000000, //CV_761 -
0b00000000, //CV_762 -
0b00000000, //CV_763 -
0b00000000, //CV_764 -
0b00000000, //CV_765 -
0b00000000, //CV_766 -
0b00000000, //CV_767 -
0b00000000, //CV_768 -
0b00000000, //CV_769 -
0b00000000, //CV_770 -
0b00000000, //CV_771 -
0b00000000, //CV_772 -
0b00000000, //CV_773 -
0b00000000, //CV_774 -
0b00000000, //CV_775 -
0b00000000, //CV_776 -
0b00000000, //CV_777 -
0b00000000, //CV_778 -
0b00000000, //CV_779 -
0b00000000, //CV_780 -
0b00000000, //CV_781 -
0b00000000, //CV_782 -
0b00000000, //CV_783 -
0b00000000, //CV_784 -
0b00000000, //CV_785 -
0b00000000, //CV_786 -
0b00000000, //CV_787 -
0b00000000, //CV_788 -
0b00000000, //CV_789 -
0b00000000, //CV_790 -
0b00000000, //CV_791 -
0b00000000, //CV_792 -
0b00000000, //CV_793 -
0b00000000, //CV_794 -
0b00000000, //CV_795 -
0b00000000, //CV_796 -
0b00000000, //CV_797 -
0b00000000, //CV_798 -
0b00000000, //CV_799 -
0b00000000, //CV_800 -
0b00000000, //CV_801 -
0b00000000, //CV_802 -
0b00000000, //CV_803 -
0b00000000, //CV_804 -
0b00000000, //CV_805 -
0b00000000, //CV_806 -
0b00000000, //CV_807 -
0b00000000, //CV_808 -
0b00000000, //CV_809 -
0b00000000, //CV_810 -
0b00000000, //CV_811 -
0b00000000, //CV_812 -
0b00000000, //CV_813 -
0b00000000, //CV_814 -
0b00000000, //CV_815 -
0b00000000, //CV_816 -
0b00000000, //CV_817 -
0b00000000, //CV_818 -
0b00000000, //CV_819 -
0b00000000, //CV_820 -
0b00000000, //CV_821 -
0b00000000, //CV_822 -
0b00000000, //CV_823 -
0b00000000, //CV_824 -
0b00000000, //CV_825 -
0b00000000, //CV_826 -
0b00000000, //CV_827 -
0b00000000, //CV_828 -
0b00000000, //CV_829 -
0b00000000, //CV_830 -
0b00000000, //CV_831 -
0b00000000, //CV_832 -
0b00000000, //CV_833 -
0b00000000, //CV_834 -
0b00000000, //CV_835 -
0b00000000, //CV_836 -
0b00000000, //CV_837 -
0b00000000, //CV_838 -
0b00000000, //CV_839 -
0b00000000, //CV_840 -
0b00000000, //CV_841 -
0b00000000, //CV_842 -
0b00000000, //CV_843 -
0b00000000, //CV_844 -
0b00000000, //CV_845 -
0b00000000, //CV_846 -
0b00000000, //CV_847 -
0b00000000, //CV_848 -
0b00000000, //CV_849 -
0b00000000, //CV_850 -
0b00000000, //CV_851 -
0b00000000, //CV_852 -
0b00000000, //CV_853 -
0b00000000, //CV_854 -
0b00000000, //CV_855 -
0b00000000, //CV_856 -
0b00000000, //CV_857 -
0b00000000, //CV_858 -
0b00000000, //CV_859 -
0b00000000, //CV_860 -
0b00000000, //CV_861 -
0b00000000, //CV_862 -
0b00000000, //CV_863 -
0b00000000, //CV_864 -
0b00000000, //CV_865 -
0b00000000, //CV_866 -
0b00000000, //CV_867 -
0b00000000, //CV_868 -
0b00000000, //CV_869 -
0b00000000, //CV_870 -
0b00000000, //CV_871 -
0b00000000, //CV_872 -
0b00000000, //CV_873 -
0b00000000, //CV_874 -
0b00000000, //CV_875 -
0b00000000, //CV_876 -
0b00000000, //CV_877 -
0b00000000, //CV_878 -
0b00000000, //CV_879 -
0b00000000, //CV_880 -
0b00000000, //CV_881 -
0b00000000, //CV_882 -
0b00000000, //CV_883 -
0b00000000, //CV_884 -
0b00000000, //CV_885 -
0b00000000, //CV_886 -
0b00000000, //CV_887 -
0b00000000, //CV_888 -
0b00000000, //CV_889 -
0b00000000, //CV_890 -
0b00000000, //CV_891 -
0b00000000, //CV_892 -
0b00000000, //CV_893 -
0b00000000, //CV_894 -
0b00000000, //CV_895 -
0b00000000, //CV_896 -
0b00000000, //CV_897 -
0b00000000, //CV_898 -
0b00000000, //CV_899 -
0b00000000, //CV_900 -
0b00000000, //CV_901 -
0b00000000, //CV_902 -
0b00000000, //CV_903 -
0b00000000, //CV_904 -
0b00000000, //CV_905 -
0b00000000, //CV_906 -
0b00000000, //CV_907 -
0b00000000, //CV_908 -
0b00000000, //CV_909 -
0b00000000, //CV_910 -
0b00000000, //CV_911 -
0b00000000, //CV_912 -
0b00000000, //CV_913 -
0b00000000, //CV_914 -
0b00000000, //CV_915 -
0b00000000, //CV_916 -
0b00000000, //CV_917 -
0b00000000, //CV_918 -
0b00000000, //CV_919 -
0b00000000, //CV_920 -
0b00000000, //CV_921 -
0b00000000, //CV_922 -
0b00000000, //CV_923 -
0b00000000, //CV_924 -
0b00000000, //CV_925 -
0b00000000, //CV_926 -
0b00000000, //CV_927 -
0b00000000, //CV_928 -
0b00000000, //CV_929 -
0b00000000, //CV_930 -
0b00000000, //CV_931 -
0b00000000, //CV_932 -
0b00000000, //CV_933 -
0b00000000, //CV_934 -
0b00000000, //CV_935 -
0b00000000, //CV_936 -
0b00000000, //CV_937 -
0b00000000, //CV_938 -
0b00000000, //CV_939 -
0b00000000, //CV_940 -
0b00000000, //CV_941 -
0b00000000, //CV_942 -
0b00000000, //CV_943 -
0b00000000, //CV_944 -
0b00000000, //CV_945 -
0b00000000, //CV_946 -
0b00000000, //CV_947 -
0b00000000, //CV_948 -
0b00000000, //CV_949 -
0b00000000, //CV_950 -
0b00000000, //CV_951 -
0b00000000, //CV_952 -
0b00000000, //CV_953 -
0b00000000, //CV_954 -
0b00000000, //CV_955 -
0b00000000, //CV_956 -
0b00000000, //CV_957 -
0b00000000, //CV_958 -
0b00000000, //CV_959 -
0b00000000, //CV_960 -
0b00000000, //CV_961 -
0b00000000, //CV_962 -
0b00000000, //CV_963 -
0b00000000, //CV_964 -
0b00000000, //CV_965 -
0b00000000, //CV_966 -
0b00000000, //CV_967 -
0b00000000, //CV_968 -
0b00000000, //CV_969 -
0b00000000, //CV_970 -
0b00000000, //CV_971 -
0b00000000, //CV_972 -
0b00000000, //CV_973 -
0b00000000, //CV_974 -
0b00000000, //CV_975 -
0b00000000, //CV_976 -
0b00000000, //CV_977 -
0b00000000, //CV_978 -
0b00000000, //CV_979 -
0b00000000, //CV_980 -
0b00000000, //CV_981 -
0b00000000, //CV_982 -
0b00000000, //CV_983 -
0b00000000, //CV_984 -
0b00000000, //CV_985 -
0b00000000, //CV_986 -
0b00000000, //CV_987 -
0b00000000, //CV_988 -
0b00000000, //CV_989 -
0b00000000, //CV_990 -
0b00000000, //CV_991 -
0b00000000, //CV_992 -
0b00000000, //CV_993 -
0b00000000, //CV_994 -
0b00000000, //CV_995 -
0b00000000, //CV_996 -
0b00000000, //CV_997 -
0b00000000, //CV_998 -
0b00000000, //CV_999 -
0b00000000, //CV_1000 -
0b00000000, //CV_1001 -
0b00000000, //CV_1002 -
0b00000000, //CV_1003 -
0b00000000, //CV_1004 -
0b00000000, //CV_1005 -
0b00000000, //CV_1006 -
0b00000000, //CV_1007 -
0b00000000, //CV_1008 -
0b00000000, //CV_1009 -
0b00000000, //CV_1010 -
0b00000000, //CV_1011 -
0b00000000, //CV_1012 -
0b00000000, //CV_1013 -
0b00000000, //CV_1014 -
0b00000000, //CV_1015 -
0b00000000, //CV_1016 -
0b00000000, //CV_1017 -
0b00000000, //CV_1018 -
0b00000000, //CV_1019 -
0b00000000, //CV_1020 -
0b00000000, //CV_1021 -
0b00000000, //CV_1022 -
0b00000000, //CV_1023 -
0b00000000, //CV_1024 -
}; };
+4 -2
View File
@@ -584,7 +584,7 @@ void cv_setup_check() {
program_mode(4, arr); //reset to CV_ARRAY_DEFAULT (write CV_8 = 8) program_mode(4, arr); //reset to CV_ARRAY_DEFAULT (write CV_8 = 8)
} }
// Check for existing ADC offset setup // Check for existing ADC offset setup TODO: always measure?
if (CV_ARRAY_FLASH[171] == 0xFF) { if (CV_ARRAY_FLASH[171] == 0xFF) {
// Write a value of 7 to read-only CV_7 in order to trigger a ADC offset measurement // Write a value of 7 to read-only CV_7 in order to trigger a ADC offset measurement
LOG(1, "found cv[171] equals to 0xff, adc offset adjstments (and cr[7] = 7)\n"); LOG(1, "found cv[171] equals to 0xff, adc offset adjstments (and cr[7] = 7)\n");
@@ -594,6 +594,7 @@ void cv_setup_check() {
// Check for base PWM configuration - used for feed-forward // Check for base PWM configuration - used for feed-forward
// Forward Direction // Forward Direction
/*
if (get_16bit_CV(175) == 0) { if (get_16bit_CV(175) == 0) {
LOG(1, "found cv[175] equals to 0, forward direction\n"); LOG(1, "found cv[175] equals to 0, forward direction\n");
const uint16_t base_pwm_fwd = measure_base_pwm(true, 10); const uint16_t base_pwm_fwd = measure_base_pwm(true, 10);
@@ -615,6 +616,7 @@ void cv_setup_check() {
const uint8_t arr1[4] = {125, base_pwm_rev_low_byte, 178, 124}; const uint8_t arr1[4] = {125, base_pwm_rev_low_byte, 178, 124};
program_mode(4, arr1); program_mode(4, arr1);
} }
*/
LOG(1, "int_lim_max %d\n", CV_ARRAY_FLASH[51]); LOG(1, "int_lim_max %d\n", CV_ARRAY_FLASH[51]);
LOG(1, "int_lim_min %d\n", CV_ARRAY_FLASH[52]); LOG(1, "int_lim_min %d\n", CV_ARRAY_FLASH[52]);
} }
@@ -666,5 +668,5 @@ int main() {
LOG(1, "core0 done\n"); LOG(1, "core0 done\n");
busy_wait_ms(100); busy_wait_ms(100);
multicore_launch_core1(core1_entry); multicore_launch_core1(core1_entry);
while (true); while (true); //sleep_ms(100); //TODO: any potential issues when using sleep?
} }
+153 -145
View File
@@ -27,7 +27,7 @@ uint8_t get_speed_step_table_index_of_speed_step(uint8_t speed_step) {
bool speed_helper(struct repeating_timer *const t) { bool speed_helper(struct repeating_timer *const t) {
// pid->setpoint only gets adjusted when the speed_helper_counter is equal to the accel_rate/decel_rate // pid->setpoint only gets adjusted when the speed_helper_counter is equal to the accel_rate/decel_rate
// -> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate) or CV_175*CV_3 or CV_175*CV_4 // -> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate) or CV_175*CV_3 or CV_175*CV_4
pid_params *const pid = (pid_params *) (t->user_data); controller_parameter_t *const pid = (controller_parameter_t *) (t->user_data);
const uint8_t accel_rate = CV_ARRAY_FLASH[2]; const uint8_t accel_rate = CV_ARRAY_FLASH[2];
const uint8_t decel_rate = CV_ARRAY_FLASH[3]; const uint8_t decel_rate = CV_ARRAY_FLASH[3];
static uint8_t speed_helper_counter; static uint8_t speed_helper_counter;
@@ -38,7 +38,7 @@ bool speed_helper(struct repeating_timer *const t) {
const bool direction_changed = get_direction_of_speed_step(speed_step_target) != const bool direction_changed = get_direction_of_speed_step(speed_step_target) !=
get_direction_of_speed_step(speed_step_target_prev); get_direction_of_speed_step(speed_step_target_prev);
if (pid->speed_step_target == 129 || pid->speed_step_target == 1) { if (speed_step_target == 129 || speed_step_target == 1) {
// Emergency Stop // Emergency Stop
speed_table_index = 0; speed_table_index = 0;
speed_helper_counter = 0; speed_helper_counter = 0;
@@ -77,7 +77,6 @@ bool speed_helper(struct repeating_timer *const t) {
return true; return true;
} }
// Helper function to adjust pwm level/duty cycle. // Helper function to adjust pwm level/duty cycle.
void adjust_pwm_level(const uint16_t level) { void adjust_pwm_level(const uint16_t level) {
if (get_direction_of_speed_step(speed_step_target)) { if (get_direction_of_speed_step(speed_step_target)) {
@@ -93,50 +92,8 @@ void adjust_pwm_level(const uint16_t level) {
} }
// Update feed-forward slope/gradient for both directions
void update_m(pid_params *const pid) {
pid->m_fwd = (pid->y_2_fwd - pid->y_1_fwd) / (pid->x_2_fwd - pid->x_1_fwd);
pid->m_rev = (pid->y_2_rev - pid->y_1_rev) / (pid->x_2_rev - pid->x_1_rev);
}
// Update feedforward function value y_2 in both directions
void update_y(pid_params *const pid, const float i) {
if (get_direction_of_speed_step(speed_step_target)) {
// Forward
pid->y_2_fwd += i * pid->k_ff;
// Limit y_2_fwd
if (pid->y_2_fwd > pid->max_output) pid->y_2_fwd = pid->max_output;
else if (pid->y_2_fwd < pid->y_1_fwd) pid->y_2_fwd = pid->y_1_fwd;
}
else {
// Reverse
pid->y_2_rev += i * pid->k_ff;
// Limit y_2_rev
if (pid->y_2_rev > pid->max_output) pid->y_2_rev = pid->max_output;
else if (pid->y_2_rev < pid->y_1_rev) pid->y_2_rev = pid->y_1_rev;
}
update_m(pid);
}
// Returns feedforward value corresponding to current setpoint
float get_ff_val(const pid_params *const pid) {
float val;
if (get_direction_of_speed_step(speed_step_target)) {
// Forward
val = pid->m_fwd * ((float) pid->setpoint - pid->x_1_fwd) + pid->y_1_fwd;
}
else {
// Reverse
val = pid->m_rev * ((float) pid->setpoint - pid->x_1_rev) + pid->y_1_rev;
}
return val;
}
// Returns proportional gain value corresponding to current setpoint // Returns proportional gain value corresponding to current setpoint
float get_kp(const pid_params *const pid) { float get_kp(const controller_parameter_t *const pid) {
const float sp = (float) pid->setpoint; const float sp = (float) pid->setpoint;
if (sp < pid->k_p_x_1) { if (sp < pid->k_p_x_1) {
return pid->k_p_m_1 * sp + pid->k_p_y_0; return pid->k_p_m_1 * sp + pid->k_p_y_0;
@@ -145,81 +102,133 @@ float get_kp(const pid_params *const pid) {
} }
// PID controller function gets called every x milliseconds where x is CV_49 aka sampling time (pid->t) uint16_t get_initial_level(controller_parameter_t *const ctrl_par){
bool pid_control(struct repeating_timer *const t) { uint32_t sum = 0;
// Cast (void *) to (pid_params *) uint32_t i = 0;
pid_params *const pid = (pid_params *) (t->user_data); while (i < 16) {
if (ctrl_par->base_pwm_arr[i] > 0) {
// Acceleration from standstill or change in direction -> reset previous derivative, error and integral parts sum += ctrl_par->base_pwm_arr[i];
const bool direction_changed = get_direction_of_speed_step(speed_step_target) != i++;
get_direction_of_speed_step(speed_step_target_prev); }
if ((!pid->setpoint_prev && !pid->setpoint) || direction_changed) { else {
pid->d_prev = 0.0f; break;
pid->i_prev = 0.0f; }
pid->e_prev = 0.0f;
} }
return ((sum / i)*2)/3;
}
// Get feed-forward and proportional gain values // Controller - Startup mode
const float feed_fwd = get_ff_val(pid); void controller_startup_mode(controller_parameter_t *const ctrl_par) {
pid->k_p = get_kp(pid); if(ctrl_par->output == 0) {
ctrl_par->output = get_initial_level(ctrl_par);
// Measure BEMF voltage and compute error }
pid->measurement = measure(pid->msr_total_iterations, if (ctrl_par->measurement_corrected < 7.5f){
pid->msr_delay_in_us, const uint16_t max_level = _125M / (CV_ARRAY_FLASH[8] * 100 + 10000);
pid->l_side_arr_cutoff, adjust_pwm_level(ctrl_par->output);
pid->r_side_arr_cutoff, ctrl_par->output += max_level / 250;
get_direction_of_speed_step(speed_step_target)); if (ctrl_par->output > max_level) {
// Try again with half val...
const float measurement_corrected = pid->measurement - pid->adc_offset; ctrl_par->output = get_initial_level(ctrl_par)/2;
const float e = (float) pid->setpoint - measurement_corrected; }
}
else {
// Save level value in array
ctrl_par->base_pwm_arr[ctrl_par->base_pwm_arr_i] = ctrl_par->output;
// Update index
ctrl_par->base_pwm_arr_i = (ctrl_par->base_pwm_arr_i+1)%16;
// Set ramp_up_mode flag to true
ctrl_par->mode = PID_MODE;
// multiply with constant value of 0.9
ctrl_par->feed_fwd = 0.9f * (float)ctrl_par->output;
}
}
// Controller - PID control mode
void controller_pid_mode(controller_parameter_t *const ctrl_par) {
ctrl_par->k_p = get_kp(ctrl_par);
// Proportional part, integral part and derivative part (including digital low-pass-filter with time constant tau) // Proportional part, integral part and derivative part (including digital low-pass-filter with time constant tau)
const float p = pid->k_p * e; float p = ctrl_par->k_p * ctrl_par->e;
float i = pid->ci_0 * (e + pid->e_prev) + pid->i_prev; float i = ctrl_par->ci_0 * (ctrl_par->e + ctrl_par->e_prev) + ctrl_par->i_prev;
const float d = pid->cd_0 * (pid->measurement - pid->measurement_prev) + pid->cd_1 * pid->d_prev; float d = ctrl_par->cd_0 * (ctrl_par->measurement - ctrl_par->measurement_prev) + ctrl_par->cd_1 * ctrl_par->d_prev;
// Check for limits on the integral part // Check for limits on the integral part
if (i > pid->int_lim_max) { if (i > ctrl_par->int_lim_max) {
i = pid->int_lim_max; i = ctrl_par->int_lim_max;
} }
else if (i < pid->int_lim_min) { else if (i < ctrl_par->int_lim_min) {
i = pid->int_lim_min; i = ctrl_par->int_lim_min;
} }
// Sum feed forward + all controller terms (p+i+d). Limit Output from 0% to 100% duty cycle // Sum feed forward + all controller terms (p+i+d). Limit Output from 0% to 100% duty cycle
float output = feed_fwd + p + i + d; float output_f = ctrl_par->feed_fwd + p + i + d;
if (output < 0 || !pid->setpoint) { if (output_f < 0) {
output = 0.0f; output_f = 0.0f;
} }
else if (output > pid->max_output) { else if (output_f > ctrl_par->max_output) {
output = pid->max_output; output_f = ctrl_par->max_output;
} }
if (LOGLEVEL >= 1) { if (LOGLEVEL >= 1) {
static int counter = 0; static int counter = 0;
counter++; counter++;
if (counter > 100) { if (counter > 100) {
LOG(1, "pid error(%f) output(%f)\n", e, output); LOG(1, "ctrl_par error(%f) output(%f)\n", ctrl_par->e, output_f);
counter = 0; counter = 0;
} }
} }
// Set PWM Level and discard results in adc fifo // Set PWM Level and discard results in adc fifo
adjust_pwm_level((uint16_t) roundf(output)); ctrl_par->output = (uint16_t) roundf(output_f);
adc_fifo_drain(); adjust_pwm_level(ctrl_par->output);
// Save previous error, integrator, differentiator values
ctrl_par->e_prev = ctrl_par->e;
ctrl_par->i_prev = i;
ctrl_par->d_prev = d;
}
// Check for High or Low Integrator values -> Update x,y values of feedforward function // General controller function gets called every x milliseconds where x is CV_49 i.e. sampling time (pid->t)
if ((output < pid->max_output && output > pid->max_output / 2) && // TODO: fixed point arithmetic to improve performance...
((i > pid->int_lim_max / 2) || (i < pid->int_lim_min / 2))) { bool controller_general(struct repeating_timer *const t) {
update_y(pid, i); // Cast (void *) to (controller_parameter_t *)
controller_parameter_t *const ctrl_par = (controller_parameter_t *) (t->user_data);
// Change in direction -> reset previous derivative, error and integral parts and pwm_base_done
const bool direction_changed = get_direction_of_speed_step(speed_step_target) !=
get_direction_of_speed_step(speed_step_target_prev);
// When setpoint == 0 there is nothing to control -> set output to 0, reset values and return
if (!ctrl_par->setpoint || direction_changed) {
ctrl_par->d_prev = 0.0f;
ctrl_par->i_prev = 0.0f;
ctrl_par->e_prev = 0.0f;
ctrl_par->mode = STARTUP_MODE;
ctrl_par->output = 0;
adjust_pwm_level(0);
// return true exits and schedule the repeating timer again
return true;
} }
// Save previous error, integrator, differentiator, direction, setpoint and measured value also sum error to e_sum // Measure BEMF voltage and compute error
pid->e_prev = e; ctrl_par->measurement = measure(ctrl_par->msr_total_iterations,
pid->i_prev = i; ctrl_par->msr_delay_in_us,
pid->d_prev = d; ctrl_par->l_side_arr_cutoff,
pid->setpoint_prev = pid->setpoint; ctrl_par->r_side_arr_cutoff,
pid->measurement_prev = pid->measurement; get_direction_of_speed_step(speed_step_target));
ctrl_par->measurement_corrected = ctrl_par->measurement - ctrl_par->adc_offset;
ctrl_par->e = (float) ctrl_par->setpoint - ctrl_par->measurement_corrected;
switch (ctrl_par->mode){
case STARTUP_MODE:
controller_startup_mode(ctrl_par);
break;
case PID_MODE:
controller_pid_mode(ctrl_par);
break;
}
adc_fifo_drain();
// Save measurement value
ctrl_par->measurement_prev = ctrl_par->measurement;
// return true to schedule the repeating timer again // return true to schedule the repeating timer again
return true; return true;
@@ -227,13 +236,21 @@ bool pid_control(struct repeating_timer *const t) {
// PID controller and measurement parameter, and speed_table initialization // PID controller and measurement parameter, and speed_table initialization
void init_pid(pid_params *const pid) { void init_controller(controller_parameter_t *const ctrl_par) {
// General controller variables
ctrl_par->feed_fwd = 0;
ctrl_par->mode = STARTUP_MODE;
ctrl_par->base_pwm_arr_i = 0;
for (int i = 0; i < BASE_PWM_ARR_LEN; ++i) {
ctrl_par->base_pwm_arr[i] = 0;
}
// Measurement variables initialization // Measurement variables initialization
pid->adc_offset = (float) CV_ARRAY_FLASH[171]; ctrl_par->adc_offset = (float) CV_ARRAY_FLASH[171];
pid->msr_total_iterations = CV_ARRAY_FLASH[60]; ctrl_par->msr_total_iterations = CV_ARRAY_FLASH[60];
pid->msr_delay_in_us = CV_ARRAY_FLASH[61]; ctrl_par->msr_delay_in_us = CV_ARRAY_FLASH[61];
pid->l_side_arr_cutoff = CV_ARRAY_FLASH[62]; ctrl_par->l_side_arr_cutoff = CV_ARRAY_FLASH[62];
pid->r_side_arr_cutoff = CV_ARRAY_FLASH[63]; ctrl_par->r_side_arr_cutoff = CV_ARRAY_FLASH[63];
// Speed table initialization // Speed table initialization
// Calculate speed setpoint table according to V_min, V_max and V_mid CVs // Calculate speed setpoint table according to V_min, V_max and V_mid CVs
@@ -246,64 +263,55 @@ void init_pid(pid_params *const pid) {
const double delta_x = 63; const double delta_x = 63;
const double m_1 = (v_mid - v_min) / delta_x; const double m_1 = (v_mid - v_min) / delta_x;
const double m_2 = (v_max - v_mid) / delta_x; const double m_2 = (v_max - v_mid) / delta_x;
pid->speed_table[0] = 0; ctrl_par->speed_table[0] = 0;
for (uint8_t i = 1; i < 64; ++i) { for (uint8_t i = 1; i < 64; ++i) {
pid->speed_table[i] = (uint16_t) lround(m_1 * (i - 1) + v_min); ctrl_par->speed_table[i] = (uint16_t) lround(m_1 * (i - 1) + v_min);
} }
for (uint8_t i = 64; i < 127; ++i) { for (uint8_t i = 64; i < 127; ++i) {
pid->speed_table[i] = (uint16_t) lround(m_2 * (i - 63) + v_mid); ctrl_par->speed_table[i] = (uint16_t) lround(m_2 * (i - 63) + v_mid);
} }
// Controller constants initialization // Controller constants initialization
pid->k_i = (float) CV_ARRAY_FLASH[49] / 10; ctrl_par->k_i = (float) CV_ARRAY_FLASH[49] / 10;
pid->k_d = (float) CV_ARRAY_FLASH[50] / 10000; ctrl_par->k_d = (float) CV_ARRAY_FLASH[50] / 10000;
pid->tau = (float) CV_ARRAY_FLASH[47] / 1000; ctrl_par->tau = (float) CV_ARRAY_FLASH[47] / 1000;
pid->t = (float) CV_ARRAY_FLASH[48] / 1000; ctrl_par->t = (float) CV_ARRAY_FLASH[48] / 1000;
pid->ci_0 = (pid->k_i * pid->t) / 2; ctrl_par->ci_0 = (ctrl_par->k_i * ctrl_par->t) / 2;
pid->cd_0 = -(2 * pid->k_d) / (2 * pid->tau + pid->t); ctrl_par->cd_0 = -(2 * ctrl_par->k_d) / (2 * ctrl_par->tau + ctrl_par->t);
pid->cd_1 = (2 * pid->tau - pid->t) / (2 * pid->tau + pid->t); ctrl_par->cd_1 = (2 * ctrl_par->tau - ctrl_par->t) / (2 * ctrl_par->tau + ctrl_par->t);
pid->int_lim_max = 10 * (float) CV_ARRAY_FLASH[51]; ctrl_par->int_lim_max = 10 * (float) CV_ARRAY_FLASH[51];
pid->int_lim_min = -10 * (float) CV_ARRAY_FLASH[52]; ctrl_par->int_lim_min = -10 * (float) CV_ARRAY_FLASH[52];
pid->k_ff = (float) CV_ARRAY_FLASH[46] / 10000; ctrl_par->max_output = (float) (_125M / (CV_ARRAY_FLASH[8] * 100 + 10000));
pid->max_output = (float) (_125M / (CV_ARRAY_FLASH[8] * 100 + 10000));
pid->x_1_rev = 0.0f;
pid->x_1_fwd = 0.0f;
pid->y_1_fwd = (float) get_16bit_CV(175);
pid->y_1_rev = (float) get_16bit_CV(177);
pid->x_2_rev = (float) pid->speed_table[126];
pid->x_2_fwd = (float) pid->speed_table[126];
// Controller variables initialization // Controller variables initialization
pid->y_2_fwd = pid->max_output; ctrl_par->output = 0;
pid->y_2_rev = pid->max_output; ctrl_par->measurement = 0.0f;
pid->measurement = 0.0f; ctrl_par->measurement_prev = 0.0f;
pid->measurement_prev = 0.0f; ctrl_par->measurement_corrected = 0.0f;
pid->e_prev = 0.0f; ctrl_par->e_prev = 0.0f;
pid->i_prev = 0.0f; ctrl_par->i_prev = 0.0f;
pid->d_prev = 0.0f; ctrl_par->d_prev = 0.0f;
pid->setpoint = 0; ctrl_par->setpoint = 0;
// Gain scheduling initialization // Gain scheduling initialization
pid->k_p_x_1_shift = (float) CV_ARRAY_FLASH[59] / 255.0f; ctrl_par->k_p_x_1_shift = (float) CV_ARRAY_FLASH[59] / 255.0f;
pid->k_p_x_1 = (float) pid->speed_table[126] * pid->k_p_x_1_shift; ctrl_par->k_p_x_1 = (float) ctrl_par->speed_table[126] * ctrl_par->k_p_x_1_shift;
pid->k_p_x_2 = (float) pid->speed_table[126] * (1.0f - pid->k_p_x_1_shift); ctrl_par->k_p_x_2 = (float) ctrl_par->speed_table[126] * (1.0f - ctrl_par->k_p_x_1_shift);
pid->k_p_y_0 = (float) get_16bit_CV(53) / 100.0f; ctrl_par->k_p_y_0 = (float) get_16bit_CV(53) / 100.0f;
pid->k_p_y_1 = (float) get_16bit_CV(55) / 100.0f; ctrl_par->k_p_y_1 = (float) get_16bit_CV(55) / 100.0f;
pid->k_p_y_2 = (float) get_16bit_CV(57) / 100.0f; ctrl_par->k_p_y_2 = (float) get_16bit_CV(57) / 100.0f;
pid->k_p_m_1 = (pid->k_p_y_1 - pid->k_p_y_0) / pid->k_p_x_1; ctrl_par->k_p_m_1 = (ctrl_par->k_p_y_1 - ctrl_par->k_p_y_0) / ctrl_par->k_p_x_1;
pid->k_p_m_2 = (pid->k_p_y_2 - pid->k_p_y_1) / pid->k_p_x_2; ctrl_par->k_p_m_2 = (ctrl_par->k_p_y_2 - ctrl_par->k_p_y_1) / ctrl_par->k_p_x_2;
update_m(pid);
} }
void core1_entry() { void core1_entry() {
LOG(1, "core1 init...\n"); LOG(1, "core1 init...\n");
pid_params pid_parameters; controller_parameter_t pid_parameters;
pid_params *pid = &pid_parameters; controller_parameter_t *pid = &pid_parameters;
init_pid(pid); init_controller(pid);
alarm_pool_add_repeating_timer_ms(alarm_pool_create(0, 1), alarm_pool_add_repeating_timer_ms(alarm_pool_create(0, 1),
CV_ARRAY_FLASH[48], CV_ARRAY_FLASH[48],
pid_control, controller_general,
pid, pid,
&pid_control_timer); &pid_control_timer);
// Set TIMER_IRQ_0 to highest priority of 0x00 // Set TIMER_IRQ_0 to highest priority of 0x00
@@ -314,5 +322,5 @@ void core1_entry() {
pid, pid,
&speed_helper_timer); &speed_helper_timer);
LOG(1, "core1 done\n"); LOG(1, "core1 done\n");
while (true); while (true); //sleep_ms(100); //TODO: any potential issues when using sleep?
} }
+44 -36
View File
@@ -8,19 +8,54 @@
#pragma once #pragma once
#include "shared.h" #include "shared.h"
#define BASE_PWM_ARR_LEN 16
typedef enum {
STARTUP_MODE,
PID_MODE,
} controller_mode_t;
typedef struct pid_params{ typedef struct pid_params{
// Controller variables - won't change after init // General Controller variables
controller_mode_t mode;
// Startup mode variables
float feed_fwd;
uint16_t base_pwm_arr[BASE_PWM_ARR_LEN];
uint16_t base_pwm_arr_i;
// PID Controller variables
float k_i; // Integral gain float k_i; // Integral gain
float k_d; // Derivative gain float k_d; // Derivative gain
float t; // Sampling time float t; // Sampling time
float tau; // Low-pass-filter time constant float tau; // Low-pass-filter time constant
float k_ff; // Feed-Forward gain
float ci_0; // (k_i*t)/2 float ci_0; // (k_i*t)/2
float cd_0; // (k_d*2)/(2*tau+t) float cd_0; // (k_d*2)/(2*tau+t)
float cd_1; // (2*tau-t)/(2*tau+t) float cd_1; // (2*tau-t)/(2*tau+t)
float int_lim_max; // max limit for integrator float int_lim_max; // max limit for integrator
float int_lim_min; // min limit for integrator float int_lim_min; // min limit for integrator
float max_output; // max possible pwm output value float max_output; // max possible pwm output value
float k_p; // Proportional gain
float e; // Error
float e_prev; // Previous Error
float i_prev; // Previous Integral Value
float d_prev; // Previous Derivative Value
uint32_t setpoint; // Current setpoint
uint16_t output;
uint16_t speed_table[127]; // Array with setpoint values corresponding to every speed step
// Measurement Variables
float measurement; // Newest Measurement value
float measurement_prev; // Previous Measurement
float measurement_corrected;
float adc_offset; // ADC offset value
uint8_t msr_delay_in_us; // Delay before VEMF Measurement
uint8_t msr_total_iterations; // Amount of samples
uint8_t l_side_arr_cutoff; // Discarded samples (left side)
uint8_t r_side_arr_cutoff; // Discarded samples (right side)
// Variable gain variables
float k_p_x_1_shift; float k_p_x_1_shift;
float k_p_x_1; float k_p_x_1;
float k_p_x_2; float k_p_x_2;
@@ -29,41 +64,14 @@ typedef struct pid_params{
float k_p_y_2; float k_p_y_2;
float k_p_m_1; float k_p_m_1;
float k_p_m_2; float k_p_m_2;
// Controller variables - might change on runtime } controller_parameter_t;
float k_p; // Proportional gain
float e_prev; // Previous Error
float i_prev; // Previous Integral Value
float d_prev; // Previous Derivative Value
float measurement_prev; // Previous Measurement
float x_1_fwd; // Base Speed; forward direction
float x_2_fwd; // High Speed; forward direction
float y_1_fwd; // Base PWM; forward direction
float y_2_fwd; // High PWM; forward direction
float x_1_rev; // Base Speed; reverse direction
float x_2_rev; // High Speed; reverse direction
float y_1_rev; // Base PWM; reverse direction
float y_2_rev; // High PWM; reverse direction
float m_fwd; // Slope forward direction
float m_rev; // Slope reverse direction
uint16_t speed_table[127]; // Array with setpoint values corresponding to every speed step
uint32_t speed_step_target; // End target speed step
uint32_t setpoint; // Current setpoint
uint32_t setpoint_prev; // Previous setpoint
// Measurement Variables
float measurement; // Newest Measurement value
float adc_offset; // ADC offset value
uint8_t msr_delay_in_us; // Delay before VEMF Measurement
uint8_t msr_total_iterations; // Amount of samples
uint8_t l_side_arr_cutoff; // Discarded samples (left side)
uint8_t r_side_arr_cutoff; // Discarded samples (right side)
}pid_params;
uint8_t get_speed_step_table_index_of_speed_step(uint8_t speed_step); uint8_t get_speed_step_table_index_of_speed_step(uint8_t speed_step);
bool speed_helper(struct repeating_timer *t); bool speed_helper(struct repeating_timer *t);
void adjust_pwm_level(uint16_t level); void adjust_pwm_level(uint16_t level);
void update_m(pid_params *pid); float get_kp(const controller_parameter_t *pid);
void update_y(pid_params *pid,float i); uint16_t get_initial_level(controller_parameter_t * ctrl_par);
float get_ff_val(const pid_params *pid); void controller_startup_mode(controller_parameter_t * ctrl_par);
float get_kp(const pid_params *pid); bool controller_general(struct repeating_timer * t);
bool pid_control(struct repeating_timer *t); void init_controller(controller_parameter_t * ctrl_par);
void init_pid( pid_params * pid);
+13 -13
View File
@@ -15,14 +15,14 @@ float measure(uint8_t total_iterations,
uint8_t measurement_delay_us, uint8_t measurement_delay_us,
uint8_t l_side_arr_cutoff, uint8_t l_side_arr_cutoff,
uint8_t r_side_arr_cutoff, uint8_t r_side_arr_cutoff,
bool direction){ bool direction) {
uint32_t sum = 0; uint32_t sum = 0;
uint16_t adc_val[total_iterations]; uint16_t adc_val[total_iterations];
int32_t j = 0; int32_t j = 0;
uint16_t key; uint16_t key;
pwm_set_gpio_level(MOTOR_FWD_PIN, 0); pwm_set_gpio_level(MOTOR_FWD_PIN, 0);
pwm_set_gpio_level(MOTOR_REV_PIN, 0); pwm_set_gpio_level(MOTOR_REV_PIN, 0);
adc_select_input((!direction)+2); adc_select_input((!direction) + 2);
busy_wait_us(measurement_delay_us); busy_wait_us(measurement_delay_us);
adc_run(true); adc_run(true);
for (int32_t i = 0; i < total_iterations; ++i) { for (int32_t i = 0; i < total_iterations; ++i) {
@@ -39,32 +39,32 @@ float measure(uint8_t total_iterations,
adc_run(false); adc_run(false);
//discard x entries beginning from the lowest entry of the array (counting up); x = msr.l_side_arr_cutoff //discard x entries beginning from the lowest entry of the array (counting up); x = msr.l_side_arr_cutoff
//discard y entries beginning from the highest index of the array (counting down); y = msr.r_side_arr_cutoff //discard y entries beginning from the highest index of the array (counting down); y = msr.r_side_arr_cutoff
for (int32_t i = l_side_arr_cutoff; i < total_iterations - r_side_arr_cutoff ; ++i) { for (int32_t i = l_side_arr_cutoff; i < total_iterations - r_side_arr_cutoff; ++i) {
sum += adc_val[i]; sum += adc_val[i];
} }
float res = (float)sum / (float)( total_iterations - (l_side_arr_cutoff + r_side_arr_cutoff) ); float res = (float) sum / (float) (total_iterations - (l_side_arr_cutoff + r_side_arr_cutoff));
// return true to keep the repeating timer active // return true to keep the repeating timer active
return res; return res;
} }
// retrieve 4Bytes from CV_ARRAY_FLASH at once and return 32-Bit value // retrieve 4Bytes from CV_ARRAY_FLASH at once and return 32-Bit value
uint32_t get_32bit_CV (uint16_t CV_start_index){ uint32_t get_32bit_CV(uint16_t CV_start_index) {
uint8_t byte_3 = CV_ARRAY_FLASH[CV_start_index]; uint8_t byte_3 = CV_ARRAY_FLASH[CV_start_index];
uint8_t byte_2 = CV_ARRAY_FLASH[CV_start_index+1]; uint8_t byte_2 = CV_ARRAY_FLASH[CV_start_index + 1];
uint8_t byte_1 = CV_ARRAY_FLASH[CV_start_index+2]; uint8_t byte_1 = CV_ARRAY_FLASH[CV_start_index + 2];
uint8_t byte_0 = CV_ARRAY_FLASH[CV_start_index+3]; uint8_t byte_0 = CV_ARRAY_FLASH[CV_start_index + 3];
return (byte_0) + (byte_1<<8) + (byte_2<<16) + (byte_3<<24); return (byte_0) + (byte_1 << 8) + (byte_2 << 16) + (byte_3 << 24);
} }
// retrieve 2Bytes from CV_ARRAY_FLASH at once and return 16-Bit value // retrieve 2Bytes from CV_ARRAY_FLASH at once and return 16-Bit value
uint16_t get_16bit_CV (uint16_t CV_start_index){ uint16_t get_16bit_CV(uint16_t CV_start_index) {
uint8_t byte_1 = CV_ARRAY_FLASH[CV_start_index]; uint8_t byte_1 = CV_ARRAY_FLASH[CV_start_index];
uint8_t byte_0 = CV_ARRAY_FLASH[CV_start_index+1]; uint8_t byte_0 = CV_ARRAY_FLASH[CV_start_index + 1];
return (byte_0) + (byte_1<<8); return (byte_0) + (byte_1 << 8);
} }
bool get_direction_of_speed_step(uint8_t speed_step){ bool get_direction_of_speed_step(uint8_t speed_step) {
// Shift by 7 Bytes to move bit7 into bit0 position and return // Shift by 7 Bytes to move bit7 into bit0 position and return
return speed_step >> 7; return speed_step >> 7;
} }