Copy code from flash to ram in order to not use XIP allowing writing to flash memory while both cores are running;
Motor control now operates with two states/modes; Extended Default CV Range to 1024 - refers to NMRA/RCN standards
This commit is contained in:
1 parent
577bc5dd5c
commit
f3ffb73b62
6 files changed
+738
-199
No files matched your search
@@ -27,7 +27,7 @@ uint8_t get_speed_step_table_index_of_speed_step(uint8_t speed_step) {
|
||||
bool speed_helper(struct repeating_timer *const t) {
|
||||
// pid->setpoint only gets adjusted when the speed_helper_counter is equal to the accel_rate/decel_rate
|
||||
// -> Time for 1 Speed Step := (speed_helper timer delay)*(accel_rate) or CV_175*CV_3 or CV_175*CV_4
|
||||
pid_params *const pid = (pid_params *) (t->user_data);
|
||||
controller_parameter_t *const pid = (controller_parameter_t *) (t->user_data);
|
||||
const uint8_t accel_rate = CV_ARRAY_FLASH[2];
|
||||
const uint8_t decel_rate = CV_ARRAY_FLASH[3];
|
||||
static uint8_t speed_helper_counter;
|
||||
@@ -38,7 +38,7 @@ bool speed_helper(struct repeating_timer *const t) {
|
||||
const bool direction_changed = get_direction_of_speed_step(speed_step_target) !=
|
||||
get_direction_of_speed_step(speed_step_target_prev);
|
||||
|
||||
if (pid->speed_step_target == 129 || pid->speed_step_target == 1) {
|
||||
if (speed_step_target == 129 || speed_step_target == 1) {
|
||||
// Emergency Stop
|
||||
speed_table_index = 0;
|
||||
speed_helper_counter = 0;
|
||||
@@ -77,7 +77,6 @@ bool speed_helper(struct repeating_timer *const t) {
|
||||
return true;
|
||||
}
|
||||
|
||||
|
||||
// Helper function to adjust pwm level/duty cycle.
|
||||
void adjust_pwm_level(const uint16_t level) {
|
||||
if (get_direction_of_speed_step(speed_step_target)) {
|
||||
@@ -93,50 +92,8 @@ void adjust_pwm_level(const uint16_t level) {
|
||||
}
|
||||
|
||||
|
||||
// Update feed-forward slope/gradient for both directions
|
||||
void update_m(pid_params *const pid) {
|
||||
pid->m_fwd = (pid->y_2_fwd - pid->y_1_fwd) / (pid->x_2_fwd - pid->x_1_fwd);
|
||||
pid->m_rev = (pid->y_2_rev - pid->y_1_rev) / (pid->x_2_rev - pid->x_1_rev);
|
||||
}
|
||||
|
||||
|
||||
// Update feedforward function value y_2 in both directions
|
||||
void update_y(pid_params *const pid, const float i) {
|
||||
if (get_direction_of_speed_step(speed_step_target)) {
|
||||
// Forward
|
||||
pid->y_2_fwd += i * pid->k_ff;
|
||||
// Limit y_2_fwd
|
||||
if (pid->y_2_fwd > pid->max_output) pid->y_2_fwd = pid->max_output;
|
||||
else if (pid->y_2_fwd < pid->y_1_fwd) pid->y_2_fwd = pid->y_1_fwd;
|
||||
}
|
||||
else {
|
||||
// Reverse
|
||||
pid->y_2_rev += i * pid->k_ff;
|
||||
// Limit y_2_rev
|
||||
if (pid->y_2_rev > pid->max_output) pid->y_2_rev = pid->max_output;
|
||||
else if (pid->y_2_rev < pid->y_1_rev) pid->y_2_rev = pid->y_1_rev;
|
||||
}
|
||||
update_m(pid);
|
||||
}
|
||||
|
||||
|
||||
// Returns feedforward value corresponding to current setpoint
|
||||
float get_ff_val(const pid_params *const pid) {
|
||||
float val;
|
||||
if (get_direction_of_speed_step(speed_step_target)) {
|
||||
// Forward
|
||||
val = pid->m_fwd * ((float) pid->setpoint - pid->x_1_fwd) + pid->y_1_fwd;
|
||||
}
|
||||
else {
|
||||
// Reverse
|
||||
val = pid->m_rev * ((float) pid->setpoint - pid->x_1_rev) + pid->y_1_rev;
|
||||
}
|
||||
return val;
|
||||
}
|
||||
|
||||
|
||||
// Returns proportional gain value corresponding to current setpoint
|
||||
float get_kp(const pid_params *const pid) {
|
||||
float get_kp(const controller_parameter_t *const pid) {
|
||||
const float sp = (float) pid->setpoint;
|
||||
if (sp < pid->k_p_x_1) {
|
||||
return pid->k_p_m_1 * sp + pid->k_p_y_0;
|
||||
@@ -145,81 +102,133 @@ float get_kp(const pid_params *const pid) {
|
||||
}
|
||||
|
||||
|
||||
// PID controller function gets called every x milliseconds where x is CV_49 aka sampling time (pid->t)
|
||||
bool pid_control(struct repeating_timer *const t) {
|
||||
// Cast (void *) to (pid_params *)
|
||||
pid_params *const pid = (pid_params *) (t->user_data);
|
||||
|
||||
// Acceleration from standstill or change in direction -> reset previous derivative, error and integral parts
|
||||
const bool direction_changed = get_direction_of_speed_step(speed_step_target) !=
|
||||
get_direction_of_speed_step(speed_step_target_prev);
|
||||
if ((!pid->setpoint_prev && !pid->setpoint) || direction_changed) {
|
||||
pid->d_prev = 0.0f;
|
||||
pid->i_prev = 0.0f;
|
||||
pid->e_prev = 0.0f;
|
||||
uint16_t get_initial_level(controller_parameter_t *const ctrl_par){
|
||||
uint32_t sum = 0;
|
||||
uint32_t i = 0;
|
||||
while (i < 16) {
|
||||
if (ctrl_par->base_pwm_arr[i] > 0) {
|
||||
sum += ctrl_par->base_pwm_arr[i];
|
||||
i++;
|
||||
}
|
||||
else {
|
||||
break;
|
||||
}
|
||||
}
|
||||
return ((sum / i)*2)/3;
|
||||
}
|
||||
|
||||
// Get feed-forward and proportional gain values
|
||||
const float feed_fwd = get_ff_val(pid);
|
||||
pid->k_p = get_kp(pid);
|
||||
|
||||
// Measure BEMF voltage and compute error
|
||||
pid->measurement = measure(pid->msr_total_iterations,
|
||||
pid->msr_delay_in_us,
|
||||
pid->l_side_arr_cutoff,
|
||||
pid->r_side_arr_cutoff,
|
||||
get_direction_of_speed_step(speed_step_target));
|
||||
|
||||
const float measurement_corrected = pid->measurement - pid->adc_offset;
|
||||
const float e = (float) pid->setpoint - measurement_corrected;
|
||||
// Controller - Startup mode
|
||||
void controller_startup_mode(controller_parameter_t *const ctrl_par) {
|
||||
if(ctrl_par->output == 0) {
|
||||
ctrl_par->output = get_initial_level(ctrl_par);
|
||||
}
|
||||
if (ctrl_par->measurement_corrected < 7.5f){
|
||||
const uint16_t max_level = _125M / (CV_ARRAY_FLASH[8] * 100 + 10000);
|
||||
adjust_pwm_level(ctrl_par->output);
|
||||
ctrl_par->output += max_level / 250;
|
||||
if (ctrl_par->output > max_level) {
|
||||
// Try again with half val...
|
||||
ctrl_par->output = get_initial_level(ctrl_par)/2;
|
||||
}
|
||||
}
|
||||
else {
|
||||
// Save level value in array
|
||||
ctrl_par->base_pwm_arr[ctrl_par->base_pwm_arr_i] = ctrl_par->output;
|
||||
// Update index
|
||||
ctrl_par->base_pwm_arr_i = (ctrl_par->base_pwm_arr_i+1)%16;
|
||||
// Set ramp_up_mode flag to true
|
||||
ctrl_par->mode = PID_MODE;
|
||||
// multiply with constant value of 0.9
|
||||
ctrl_par->feed_fwd = 0.9f * (float)ctrl_par->output;
|
||||
}
|
||||
}
|
||||
|
||||
// Controller - PID control mode
|
||||
void controller_pid_mode(controller_parameter_t *const ctrl_par) {
|
||||
ctrl_par->k_p = get_kp(ctrl_par);
|
||||
// Proportional part, integral part and derivative part (including digital low-pass-filter with time constant tau)
|
||||
const float p = pid->k_p * e;
|
||||
float i = pid->ci_0 * (e + pid->e_prev) + pid->i_prev;
|
||||
const float d = pid->cd_0 * (pid->measurement - pid->measurement_prev) + pid->cd_1 * pid->d_prev;
|
||||
float p = ctrl_par->k_p * ctrl_par->e;
|
||||
float i = ctrl_par->ci_0 * (ctrl_par->e + ctrl_par->e_prev) + ctrl_par->i_prev;
|
||||
float d = ctrl_par->cd_0 * (ctrl_par->measurement - ctrl_par->measurement_prev) + ctrl_par->cd_1 * ctrl_par->d_prev;
|
||||
|
||||
// Check for limits on the integral part
|
||||
if (i > pid->int_lim_max) {
|
||||
i = pid->int_lim_max;
|
||||
if (i > ctrl_par->int_lim_max) {
|
||||
i = ctrl_par->int_lim_max;
|
||||
}
|
||||
else if (i < pid->int_lim_min) {
|
||||
i = pid->int_lim_min;
|
||||
else if (i < ctrl_par->int_lim_min) {
|
||||
i = ctrl_par->int_lim_min;
|
||||
}
|
||||
|
||||
// Sum feed forward + all controller terms (p+i+d). Limit Output from 0% to 100% duty cycle
|
||||
float output = feed_fwd + p + i + d;
|
||||
if (output < 0 || !pid->setpoint) {
|
||||
output = 0.0f;
|
||||
float output_f = ctrl_par->feed_fwd + p + i + d;
|
||||
if (output_f < 0) {
|
||||
output_f = 0.0f;
|
||||
}
|
||||
else if (output > pid->max_output) {
|
||||
output = pid->max_output;
|
||||
else if (output_f > ctrl_par->max_output) {
|
||||
output_f = ctrl_par->max_output;
|
||||
}
|
||||
|
||||
if (LOGLEVEL >= 1) {
|
||||
static int counter = 0;
|
||||
counter++;
|
||||
if (counter > 100) {
|
||||
LOG(1, "pid error(%f) output(%f)\n", e, output);
|
||||
LOG(1, "ctrl_par error(%f) output(%f)\n", ctrl_par->e, output_f);
|
||||
counter = 0;
|
||||
}
|
||||
}
|
||||
|
||||
// Set PWM Level and discard results in adc fifo
|
||||
adjust_pwm_level((uint16_t) roundf(output));
|
||||
adc_fifo_drain();
|
||||
ctrl_par->output = (uint16_t) roundf(output_f);
|
||||
adjust_pwm_level(ctrl_par->output);
|
||||
// Save previous error, integrator, differentiator values
|
||||
ctrl_par->e_prev = ctrl_par->e;
|
||||
ctrl_par->i_prev = i;
|
||||
ctrl_par->d_prev = d;
|
||||
}
|
||||
|
||||
// Check for High or Low Integrator values -> Update x,y values of feedforward function
|
||||
if ((output < pid->max_output && output > pid->max_output / 2) &&
|
||||
((i > pid->int_lim_max / 2) || (i < pid->int_lim_min / 2))) {
|
||||
update_y(pid, i);
|
||||
// General controller function gets called every x milliseconds where x is CV_49 i.e. sampling time (pid->t)
|
||||
// TODO: fixed point arithmetic to improve performance...
|
||||
bool controller_general(struct repeating_timer *const t) {
|
||||
// Cast (void *) to (controller_parameter_t *)
|
||||
controller_parameter_t *const ctrl_par = (controller_parameter_t *) (t->user_data);
|
||||
|
||||
// Change in direction -> reset previous derivative, error and integral parts and pwm_base_done
|
||||
const bool direction_changed = get_direction_of_speed_step(speed_step_target) !=
|
||||
get_direction_of_speed_step(speed_step_target_prev);
|
||||
// When setpoint == 0 there is nothing to control -> set output to 0, reset values and return
|
||||
if (!ctrl_par->setpoint || direction_changed) {
|
||||
ctrl_par->d_prev = 0.0f;
|
||||
ctrl_par->i_prev = 0.0f;
|
||||
ctrl_par->e_prev = 0.0f;
|
||||
ctrl_par->mode = STARTUP_MODE;
|
||||
ctrl_par->output = 0;
|
||||
adjust_pwm_level(0);
|
||||
// return true exits and schedule the repeating timer again
|
||||
return true;
|
||||
}
|
||||
|
||||
// Save previous error, integrator, differentiator, direction, setpoint and measured value also sum error to e_sum
|
||||
pid->e_prev = e;
|
||||
pid->i_prev = i;
|
||||
pid->d_prev = d;
|
||||
pid->setpoint_prev = pid->setpoint;
|
||||
pid->measurement_prev = pid->measurement;
|
||||
// Measure BEMF voltage and compute error
|
||||
ctrl_par->measurement = measure(ctrl_par->msr_total_iterations,
|
||||
ctrl_par->msr_delay_in_us,
|
||||
ctrl_par->l_side_arr_cutoff,
|
||||
ctrl_par->r_side_arr_cutoff,
|
||||
get_direction_of_speed_step(speed_step_target));
|
||||
ctrl_par->measurement_corrected = ctrl_par->measurement - ctrl_par->adc_offset;
|
||||
ctrl_par->e = (float) ctrl_par->setpoint - ctrl_par->measurement_corrected;
|
||||
|
||||
switch (ctrl_par->mode){
|
||||
case STARTUP_MODE:
|
||||
controller_startup_mode(ctrl_par);
|
||||
break;
|
||||
case PID_MODE:
|
||||
controller_pid_mode(ctrl_par);
|
||||
break;
|
||||
}
|
||||
|
||||
adc_fifo_drain();
|
||||
|
||||
// Save measurement value
|
||||
ctrl_par->measurement_prev = ctrl_par->measurement;
|
||||
|
||||
// return true to schedule the repeating timer again
|
||||
return true;
|
||||
@@ -227,13 +236,21 @@ bool pid_control(struct repeating_timer *const t) {
|
||||
|
||||
|
||||
// PID controller and measurement parameter, and speed_table initialization
|
||||
void init_pid(pid_params *const pid) {
|
||||
void init_controller(controller_parameter_t *const ctrl_par) {
|
||||
// General controller variables
|
||||
ctrl_par->feed_fwd = 0;
|
||||
ctrl_par->mode = STARTUP_MODE;
|
||||
ctrl_par->base_pwm_arr_i = 0;
|
||||
for (int i = 0; i < BASE_PWM_ARR_LEN; ++i) {
|
||||
ctrl_par->base_pwm_arr[i] = 0;
|
||||
}
|
||||
|
||||
// Measurement variables initialization
|
||||
pid->adc_offset = (float) CV_ARRAY_FLASH[171];
|
||||
pid->msr_total_iterations = CV_ARRAY_FLASH[60];
|
||||
pid->msr_delay_in_us = CV_ARRAY_FLASH[61];
|
||||
pid->l_side_arr_cutoff = CV_ARRAY_FLASH[62];
|
||||
pid->r_side_arr_cutoff = CV_ARRAY_FLASH[63];
|
||||
ctrl_par->adc_offset = (float) CV_ARRAY_FLASH[171];
|
||||
ctrl_par->msr_total_iterations = CV_ARRAY_FLASH[60];
|
||||
ctrl_par->msr_delay_in_us = CV_ARRAY_FLASH[61];
|
||||
ctrl_par->l_side_arr_cutoff = CV_ARRAY_FLASH[62];
|
||||
ctrl_par->r_side_arr_cutoff = CV_ARRAY_FLASH[63];
|
||||
|
||||
// Speed table initialization
|
||||
// Calculate speed setpoint table according to V_min, V_max and V_mid CVs
|
||||
@@ -246,64 +263,55 @@ void init_pid(pid_params *const pid) {
|
||||
const double delta_x = 63;
|
||||
const double m_1 = (v_mid - v_min) / delta_x;
|
||||
const double m_2 = (v_max - v_mid) / delta_x;
|
||||
pid->speed_table[0] = 0;
|
||||
ctrl_par->speed_table[0] = 0;
|
||||
for (uint8_t i = 1; i < 64; ++i) {
|
||||
pid->speed_table[i] = (uint16_t) lround(m_1 * (i - 1) + v_min);
|
||||
ctrl_par->speed_table[i] = (uint16_t) lround(m_1 * (i - 1) + v_min);
|
||||
}
|
||||
for (uint8_t i = 64; i < 127; ++i) {
|
||||
pid->speed_table[i] = (uint16_t) lround(m_2 * (i - 63) + v_mid);
|
||||
ctrl_par->speed_table[i] = (uint16_t) lround(m_2 * (i - 63) + v_mid);
|
||||
}
|
||||
|
||||
// Controller constants initialization
|
||||
pid->k_i = (float) CV_ARRAY_FLASH[49] / 10;
|
||||
pid->k_d = (float) CV_ARRAY_FLASH[50] / 10000;
|
||||
pid->tau = (float) CV_ARRAY_FLASH[47] / 1000;
|
||||
pid->t = (float) CV_ARRAY_FLASH[48] / 1000;
|
||||
pid->ci_0 = (pid->k_i * pid->t) / 2;
|
||||
pid->cd_0 = -(2 * pid->k_d) / (2 * pid->tau + pid->t);
|
||||
pid->cd_1 = (2 * pid->tau - pid->t) / (2 * pid->tau + pid->t);
|
||||
pid->int_lim_max = 10 * (float) CV_ARRAY_FLASH[51];
|
||||
pid->int_lim_min = -10 * (float) CV_ARRAY_FLASH[52];
|
||||
pid->k_ff = (float) CV_ARRAY_FLASH[46] / 10000;
|
||||
pid->max_output = (float) (_125M / (CV_ARRAY_FLASH[8] * 100 + 10000));
|
||||
pid->x_1_rev = 0.0f;
|
||||
pid->x_1_fwd = 0.0f;
|
||||
pid->y_1_fwd = (float) get_16bit_CV(175);
|
||||
pid->y_1_rev = (float) get_16bit_CV(177);
|
||||
pid->x_2_rev = (float) pid->speed_table[126];
|
||||
pid->x_2_fwd = (float) pid->speed_table[126];
|
||||
ctrl_par->k_i = (float) CV_ARRAY_FLASH[49] / 10;
|
||||
ctrl_par->k_d = (float) CV_ARRAY_FLASH[50] / 10000;
|
||||
ctrl_par->tau = (float) CV_ARRAY_FLASH[47] / 1000;
|
||||
ctrl_par->t = (float) CV_ARRAY_FLASH[48] / 1000;
|
||||
ctrl_par->ci_0 = (ctrl_par->k_i * ctrl_par->t) / 2;
|
||||
ctrl_par->cd_0 = -(2 * ctrl_par->k_d) / (2 * ctrl_par->tau + ctrl_par->t);
|
||||
ctrl_par->cd_1 = (2 * ctrl_par->tau - ctrl_par->t) / (2 * ctrl_par->tau + ctrl_par->t);
|
||||
ctrl_par->int_lim_max = 10 * (float) CV_ARRAY_FLASH[51];
|
||||
ctrl_par->int_lim_min = -10 * (float) CV_ARRAY_FLASH[52];
|
||||
ctrl_par->max_output = (float) (_125M / (CV_ARRAY_FLASH[8] * 100 + 10000));
|
||||
|
||||
// Controller variables initialization
|
||||
pid->y_2_fwd = pid->max_output;
|
||||
pid->y_2_rev = pid->max_output;
|
||||
pid->measurement = 0.0f;
|
||||
pid->measurement_prev = 0.0f;
|
||||
pid->e_prev = 0.0f;
|
||||
pid->i_prev = 0.0f;
|
||||
pid->d_prev = 0.0f;
|
||||
pid->setpoint = 0;
|
||||
ctrl_par->output = 0;
|
||||
ctrl_par->measurement = 0.0f;
|
||||
ctrl_par->measurement_prev = 0.0f;
|
||||
ctrl_par->measurement_corrected = 0.0f;
|
||||
ctrl_par->e_prev = 0.0f;
|
||||
ctrl_par->i_prev = 0.0f;
|
||||
ctrl_par->d_prev = 0.0f;
|
||||
ctrl_par->setpoint = 0;
|
||||
|
||||
// Gain scheduling initialization
|
||||
pid->k_p_x_1_shift = (float) CV_ARRAY_FLASH[59] / 255.0f;
|
||||
pid->k_p_x_1 = (float) pid->speed_table[126] * pid->k_p_x_1_shift;
|
||||
pid->k_p_x_2 = (float) pid->speed_table[126] * (1.0f - pid->k_p_x_1_shift);
|
||||
pid->k_p_y_0 = (float) get_16bit_CV(53) / 100.0f;
|
||||
pid->k_p_y_1 = (float) get_16bit_CV(55) / 100.0f;
|
||||
pid->k_p_y_2 = (float) get_16bit_CV(57) / 100.0f;
|
||||
pid->k_p_m_1 = (pid->k_p_y_1 - pid->k_p_y_0) / pid->k_p_x_1;
|
||||
pid->k_p_m_2 = (pid->k_p_y_2 - pid->k_p_y_1) / pid->k_p_x_2;
|
||||
|
||||
update_m(pid);
|
||||
ctrl_par->k_p_x_1_shift = (float) CV_ARRAY_FLASH[59] / 255.0f;
|
||||
ctrl_par->k_p_x_1 = (float) ctrl_par->speed_table[126] * ctrl_par->k_p_x_1_shift;
|
||||
ctrl_par->k_p_x_2 = (float) ctrl_par->speed_table[126] * (1.0f - ctrl_par->k_p_x_1_shift);
|
||||
ctrl_par->k_p_y_0 = (float) get_16bit_CV(53) / 100.0f;
|
||||
ctrl_par->k_p_y_1 = (float) get_16bit_CV(55) / 100.0f;
|
||||
ctrl_par->k_p_y_2 = (float) get_16bit_CV(57) / 100.0f;
|
||||
ctrl_par->k_p_m_1 = (ctrl_par->k_p_y_1 - ctrl_par->k_p_y_0) / ctrl_par->k_p_x_1;
|
||||
ctrl_par->k_p_m_2 = (ctrl_par->k_p_y_2 - ctrl_par->k_p_y_1) / ctrl_par->k_p_x_2;
|
||||
}
|
||||
|
||||
void core1_entry() {
|
||||
LOG(1, "core1 init...\n");
|
||||
pid_params pid_parameters;
|
||||
pid_params *pid = &pid_parameters;
|
||||
init_pid(pid);
|
||||
controller_parameter_t pid_parameters;
|
||||
controller_parameter_t *pid = &pid_parameters;
|
||||
init_controller(pid);
|
||||
alarm_pool_add_repeating_timer_ms(alarm_pool_create(0, 1),
|
||||
CV_ARRAY_FLASH[48],
|
||||
pid_control,
|
||||
controller_general,
|
||||
pid,
|
||||
&pid_control_timer);
|
||||
// Set TIMER_IRQ_0 to highest priority of 0x00
|
||||
@@ -314,5 +322,5 @@ void core1_entry() {
|
||||
pid,
|
||||
&speed_helper_timer);
|
||||
LOG(1, "core1 done\n");
|
||||
while (true);
|
||||
while (true); //sleep_ms(100); //TODO: any potential issues when using sleep?
|
||||
}
|
||||
Reference in new issue
Block a user