Moved all software related files to Software folder; Now using flash safe execution functions of pico_flash (pico SDK) lib; Added error handling; Added RP2040-Decoder-board.h definition; Adapted CMakeLists.txt for use with vscode pi pico extension;
This commit is contained in:
1 parent
e8a8ac6d98
commit
7b1d5ed152
12 files changed
+1452
-1271
No files matched your search
@@ -0,0 +1,119 @@
|
||||
/*!
|
||||
*
|
||||
* \file shared.h
|
||||
* Used by both cores
|
||||
*
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
#include "string.h"
|
||||
#include "pico/float.h"
|
||||
#include "pico/stdlib.h"
|
||||
#include "pico/multicore.h"
|
||||
#include "pico/printf.h"
|
||||
#include "pico/flash.h"
|
||||
#include "hardware/pwm.h"
|
||||
#include "hardware/adc.h"
|
||||
#include "hardware/flash.h"
|
||||
#include "hardware/gpio.h"
|
||||
|
||||
typedef enum {
|
||||
FLASH_SAFE_EXECUTE_CORE_INIT_FAILURE = (1<<0),
|
||||
FLASH_SAFE_EXECUTE_ERASE_FAILURE = (1<<1),
|
||||
FLASH_SAFE_EXECUTE_PROGRAM_FAILURE = (1<<2),
|
||||
FLASH_SIZE_READBACK_FAILURE = (1<<3),
|
||||
STDIO_INIT_FAILURE = (1<<4),
|
||||
} error_t;
|
||||
|
||||
|
||||
// here you can enable printf debugging (needs extra soldering and you have to enable uart in the cmake configuration)
|
||||
// please note
|
||||
// - if it's disabled it will be compiled completely out
|
||||
// - be careful that printf debugging can change your timing behavior, for example in the pid controller limit the outputs
|
||||
// like already done (only print every 100th iteration for example!)
|
||||
// - also note that with logging enabled GPIO0/1 are DISABLED from decoder functions because they are used for uart to the
|
||||
// outside world (this is configure automatically for you below!)
|
||||
// - IMPORTANT: you have to enable uart in the cmakelists.txt to enable logging!
|
||||
#define LOGLEVEL 1
|
||||
#define LOG(level, ...) { if(level <= LOGLEVEL) {printf(__VA_ARGS__);}}
|
||||
|
||||
// Constant Value of 125 x 10^6
|
||||
#define _125M 125000000
|
||||
|
||||
// GPIO used for DCC-Signal, Motor PWM or ADC
|
||||
#define DCC_INPUT_PIN 21u
|
||||
#define MOTOR_FWD_PIN 23u
|
||||
#define MOTOR_REV_PIN 22u
|
||||
#define FWD_V_EMF_ADC_PIN 28u
|
||||
#define REV_V_EMF_ADC_PIN 29u
|
||||
|
||||
// if logging is enabled do NOT use gpio0/1 for functions in the decoder
|
||||
#if LOGLEVEL != 0
|
||||
// GPIO used directly (GPIO 2-5 incl.) as outputs or to switch auxiliary output transistors (GPIO 24-27 incl.)
|
||||
#define GPIO_OUTPUT_PIN_MASK (1u<<24) | (1u<<25) | (1u<<26) | (1u<<27) | (1u<<5) | (1u<<4) | (1u<<3) | (1u<<2)
|
||||
#else
|
||||
// GPIO used directly (GPIO 0-5 incl.) as outputs or to switch auxiliary output transistors (GPIO 24-27 incl.)
|
||||
#define GPIO_OUTPUT_PIN_MASK (1u<<24) | (1u<<25) | (1u<<26) | (1u<<27) | (1u<<5) | (1u<<4) | (1u<<3) | (1u<<2) | (1u<<1) | (1u<<0)
|
||||
#endif
|
||||
|
||||
// GPIO pin mask to prevent setting illegal GPIOs (ADC, Motor, DCC Input Pin)
|
||||
#define GPIO_ILLEGAL_MASK (1u<<DCC_INPUT_PIN) | (1u<<MOTOR_FWD_PIN) | (1u<<MOTOR_REV_PIN) | (1u<<FWD_V_EMF_ADC_PIN) | (1u<<REV_V_EMF_ADC_PIN)
|
||||
|
||||
// GPIO pin mask with allowed outputs (AUX & GPIO (configured as outputs))
|
||||
#define GPIO_ALLOWED_OUTPUTS (GPIO_OUTPUT_PIN_MASK) & ~(GPIO_ILLEGAL_MASK)
|
||||
|
||||
|
||||
extern repeating_timer_t pid_control_timer;
|
||||
extern repeating_timer_t speed_helper_timer;
|
||||
extern const uint8_t *CV_ARRAY_FLASH;
|
||||
extern uint8_t speed_step_target;
|
||||
extern uint8_t speed_step_target_prev;
|
||||
|
||||
|
||||
void core1_entry();
|
||||
void write_cv_handler(uint16_t cv_index, uint8_t cv_data);
|
||||
float measure(uint8_t total_iterations,
|
||||
uint8_t measurement_delay_us,
|
||||
uint8_t l_side_arr_cutoff,
|
||||
uint8_t r_side_arr_cutoff,
|
||||
bool direction);
|
||||
uint32_t get_32bit_CV (uint16_t CV_start_index);
|
||||
uint16_t get_16bit_CV (uint16_t CV_start_index);
|
||||
/*!
|
||||
* @brief Calculates the direction based on a speed step byte.
|
||||
*
|
||||
* This function calculates the direction of movement based on the value of
|
||||
* the `speed_step` byte. It refers to the "128 Speed Control" standard as outlined
|
||||
* in NMRA Standard 9.2.1 section 2.3.2.1 or RCN-212 section 2.2.2.
|
||||
*
|
||||
* The following speed steps are defined:
|
||||
*
|
||||
* | DEC | BIN | DIRECTION | DEFINITION |
|
||||
* |-----|-----------|-----------|----------------------|
|
||||
* | 000 | 0000 0000 | Reverse | STOP |
|
||||
* | 001 | 0000 0001 | Reverse | EMERGENCY STOP |
|
||||
* | 002 | 0000 0010 | Reverse | Speed step 001 |
|
||||
* | 003 | 0000 0011 | Reverse | Speed step 002 |
|
||||
* | 004 | 0000 0100 | Reverse | Speed step 003 |
|
||||
* | ... | .... .... | Reverse | ... |
|
||||
* | 126 | 0111 1110 | Reverse | Speed step 125 |
|
||||
* | 127 | 0111 1111 | Reverse | Speed step 126 |
|
||||
* | 128 | 1000 0000 | Forward | STOP |
|
||||
* | 129 | 1000 0001 | Forward | EMERGENCY STOP |
|
||||
* | 130 | 1000 0010 | Forward | Speed step 001 |
|
||||
* | 131 | 1000 0011 | Forward | Speed step 002 |
|
||||
* | 132 | 1000 0100 | Forward | Speed step 003 |
|
||||
* | ... | .... .... | Forward | ... |
|
||||
* | 254 | 1111 1110 | Forward | Speed step 125 |
|
||||
* | 255 | 1111 1111 | Forward | Speed step 126 |
|
||||
*
|
||||
* @param speed_step The speed step byte.
|
||||
* @return `true` for forward direction, `false` for reverse direction.
|
||||
*/
|
||||
bool get_direction_of_speed_step(uint8_t speed_step);
|
||||
|
||||
void set_error(error_t err);
|
||||
|
||||
void clear_error(error_t err);
|
||||
|
||||
uint32_t get_error_state();
|
||||
Reference in new issue
Block a user