pure sdk for main
This commit is contained in:
divadiow
@@ -0,0 +1,957 @@
|
||||
#include "sys_config.h"
|
||||
#include "typesdef.h"
|
||||
#include "dev.h"
|
||||
#include "devid.h"
|
||||
#include "hal/gpio.h"
|
||||
#include "hal/dvp.h"
|
||||
#include "hal/vpp.h"
|
||||
#include "hal/adc.h"
|
||||
#include "hal/spi.h"
|
||||
#include "osal/irq.h"
|
||||
#include "osal/string.h"
|
||||
#include "hal/pwm.h"
|
||||
#include "hal/timer_device.h"
|
||||
#include "osal/task.h"
|
||||
|
||||
#if PRINTER_EN
|
||||
|
||||
/*==================================打印机引脚定义==================================*/
|
||||
#define MOTO_SLEEP_PIN PB_7 // LOW sleep , HIGH run
|
||||
|
||||
#define PRINTER_DATA_PIN PB_13
|
||||
#define PRINTER_CLK_PIN PB_11
|
||||
#define PRINTER_LATCH_PIN PB_8
|
||||
#define PRINTER_TM_PIN PC_5
|
||||
#define PRINTER_PSENSOR_PIN PA_0
|
||||
#define PRINTER_STB_PIN PB_10
|
||||
#define PRINTER_EN_PIN PA_7
|
||||
|
||||
#define PRINTER_DATA_PORT GPIOB
|
||||
#define PRINTER_DATA_NUM 13
|
||||
#define PRINTER_CLK_PORT GPIOB
|
||||
#define PRINTER_CLK_NUM 11
|
||||
#define PRINTER_STB_PORT GPIOB
|
||||
#define PRINTER_STB_NUM 10
|
||||
|
||||
#define PRINTER_W 384
|
||||
#define PRINTER_H 512
|
||||
|
||||
|
||||
/*
|
||||
第一组PWM (3.59 s): 打开SPI_SEND_EN、关闭STB_PIN_PWM_EN
|
||||
printer_delay: 1,7
|
||||
|
||||
第二组PWM (4.62 s)： 关闭SPI_SEND_EN、打开STB_PIN_PWM_EN
|
||||
printer_delay： 1,17
|
||||
|
||||
(4.63 s): 打开SPI_SEND_EN、关闭STB_PIN_PWM_EN
|
||||
printer_delay： 1,53
|
||||
|
||||
第三组PWM (6.16 s)： 关闭SPI_SEND_EN、打开STB_PIN_PWM_EN
|
||||
printer_delay: 21,57
|
||||
|
||||
(6.18 s): 打开SPI_SEND_EN、打开STB_PIN_PWM_EN
|
||||
printer_delay: 21,86
|
||||
|
||||
第四组PWM（8.19 s）：打开SPI_SEND_EN、打开STB_PIN_PWM_EN
|
||||
printer_delay: 1,26
|
||||
*/
|
||||
#define PRINTER_PWM_1_EN 0
|
||||
#define PRINTER_PWM_2_EN 0
|
||||
#define PRINTER_PWM_3_EN 1
|
||||
#define PRINTER_PWM_4_EN 0
|
||||
|
||||
/*====================================第一组 PWM====================================*/
|
||||
#if PRINTER_PWM_1_EN
|
||||
|
||||
#define SPI_SEND_EN 1 //使用SPI时序发送数据，可控发送速率
|
||||
#define STB_PIN_PWM_EN 1 //STB 使用PWM波形，使能置1否则置0
|
||||
|
||||
#define TOTAL_TICK 256 //打印每行调用timer7_noisr_func函数的次数
|
||||
|
||||
#define SPI_CLK_FREQ 8000000 //SPI时钟频率8M ，CLK脚高电平稳定时间约为50-60ns
|
||||
#define STB_PIN_PWM_PERIOD 1000
|
||||
#define STB_PIN_PWM_DUTY 900 //改变PWM的占空比可以改变加热时长
|
||||
#define DELAY_NOHEAT 1
|
||||
#define DELAY_HEAT 7
|
||||
|
||||
|
||||
/*====================================第二组 PWM====================================*/
|
||||
#elif PRINTER_PWM_2_EN
|
||||
|
||||
#define SPI_SEND_EN 1 //使用SPI时序发送数据，可控发送速率
|
||||
#define STB_PIN_PWM_EN 1 //STB 使用PWM波形，使能置1否则置0
|
||||
|
||||
#define TOTAL_TICK 256 //打印每行调用timer7_noisr_func函数的次数
|
||||
|
||||
#if SPI_SEND_EN
|
||||
#define SPI_CLK_FREQ 8000000 //SPI时钟频率8M ，CLK脚高电平稳定时间约为50-60ns
|
||||
#define STB_PIN_PWM_PERIOD 1000
|
||||
#define STB_PIN_PWM_DUTY 900 //改变PWM的占空比可以改变加热时长
|
||||
#define DELAY_NOHEAT 1
|
||||
#define DELAY_HEAT 53
|
||||
#else
|
||||
#define SPI_CLK_FREQ 8000000 //SPI时钟频率8M ，CLK脚高电平稳定时间约为50-60ns
|
||||
#define STB_PIN_PWM_PERIOD 1000
|
||||
#define STB_PIN_PWM_DUTY 900 //改变PWM的占空比可以改变加热时长
|
||||
#define DELAY_NOHEAT 1
|
||||
#define DELAY_HEAT 17
|
||||
#endif
|
||||
|
||||
/*====================================第三组 PWM====================================*/
|
||||
#elif PRINTER_PWM_3_EN
|
||||
|
||||
#define SPI_SEND_EN 1 //使用SPI时序发送数据，可控发送速率
|
||||
#define STB_PIN_PWM_EN 0 //STB 使用PWM波形，使能置1否则置0
|
||||
#define HEAT_MOTO_SEPARATION (1 && SPI_SEND_EN)
|
||||
|
||||
#define TOTAL_TICK 256 //打印每行调用timer7_noisr_func函数的次数
|
||||
|
||||
#if SPI_SEND_EN
|
||||
#define SPI_CLK_FREQ 8000000 //SPI时钟频率8M ，CLK脚高电平稳定时间约为50-60ns
|
||||
#define STB_PIN_PWM_PERIOD 1000
|
||||
#define STB_PIN_PWM_DUTY 600 //改变PWM的占空比可以改变加热时长
|
||||
#define DELAY_NOHEAT 1
|
||||
#define DELAY_HEAT 106
|
||||
#else
|
||||
#define SPI_CLK_FREQ 8000000 //SPI时钟频率8M ，CLK脚高电平稳定时间约为50-60ns
|
||||
#define STB_PIN_PWM_PERIOD 1000
|
||||
#define STB_PIN_PWM_DUTY 600 //改变PWM的占空比可以改变加热时长
|
||||
#define DELAY_NOHEAT 21
|
||||
#define DELAY_HEAT 57
|
||||
#endif
|
||||
|
||||
/*====================================第四组 PWM====================================*/
|
||||
#elif PRINTER_PWM_4_EN
|
||||
|
||||
#define SPI_SEND_EN 1 //该组暂时只能置1
|
||||
#define STB_PIN_PWM_EN 0 //STB 使用PWM波形，使能置1否则置0
|
||||
|
||||
#define TOTAL_TICK 512 //打印每行调用timer7_noisr_func函数的次数
|
||||
|
||||
#if SPI_SEND_EN
|
||||
#define SPI_CLK_FREQ 8000000 //SPI时钟频率8M ，CLK脚高电平稳定时间约为50-60ns
|
||||
#define STB_PIN_PWM_PERIOD 1000
|
||||
#define STB_PIN_PWM_DUTY 900 //改变PWM的占空比可以改变加热时长
|
||||
#define DELAY_NOHEAT 1
|
||||
#define DELAY_HEAT 26
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
struct hgpwm_v0 *moto_hgpwm;
|
||||
struct hgadc_v0* hgadc_tm;
|
||||
struct timer_device* tmr7_dev_g;
|
||||
struct os_task handle_printer_task;
|
||||
|
||||
extern const unsigned char printer_demo[196608]; //384 x 512 只包含Y数据的图片
|
||||
uint8 printer_buf[196608] __attribute__ ((aligned(4),section(".psram.src"))); //384 x 512
|
||||
#if SPI_SEND_EN
|
||||
struct spi_device *spi0_dev;
|
||||
uint8 printer_buf_odd[48] __attribute__ ((aligned(4))); //48*8 = 384
|
||||
uint8 printer_buf_even[48] __attribute__ ((aligned(4))); //48*8 = 384
|
||||
#endif
|
||||
const unsigned char *printer_picture_addr;
|
||||
volatile uint32_t printer_h = 0;
|
||||
|
||||
typedef struct {
|
||||
__IO uint32_t MODE;
|
||||
__IO uint32_t OTYPE;
|
||||
__IO uint32_t OSPEEDL;
|
||||
__IO uint32_t OSPEEDH;
|
||||
__IO uint32_t PUPL;
|
||||
__IO uint32_t PUPH;
|
||||
__IO uint32_t PUDL;
|
||||
__IO uint32_t PUDH;
|
||||
__IO uint32_t IDAT;
|
||||
__IO uint32_t ODAT;
|
||||
__IO uint32_t BSR;
|
||||
__IO uint32_t RES0;
|
||||
__IO uint32_t AFRL;
|
||||
__IO uint32_t AFRH;
|
||||
__IO uint32_t TGL;
|
||||
__IO uint32_t IMK;
|
||||
__IO uint32_t RES1;
|
||||
__IO uint32_t RES2;
|
||||
__IO uint32_t RES3;
|
||||
__IO uint32_t DEBEN;
|
||||
__IO uint32_t AIOEN;
|
||||
__IO uint32_t PND;
|
||||
__IO uint32_t PNDCLR;
|
||||
__IO uint32_t TRG0;
|
||||
__IO uint32_t RES4;
|
||||
__IO uint32_t RES5;
|
||||
__IO uint32_t RES6;
|
||||
__IO uint32_t RES7;
|
||||
__IO uint32_t IEEN;
|
||||
__IO uint32_t IOFUNCOUTCON0;
|
||||
__IO uint32_t IOFUNCOUTCON1;
|
||||
__IO uint32_t IOFUNCOUTCON2;
|
||||
__IO uint32_t IOFUNCOUTCON3;
|
||||
} GPIO_TypeDef;
|
||||
|
||||
#define GPIOA ((GPIO_TypeDef *) HG_GPIOA_BASE)
|
||||
#define GPIOB ((GPIO_TypeDef *) HG_GPIOB_BASE)
|
||||
#define GPIOC ((GPIO_TypeDef *) HG_GPIOC_BASE)
|
||||
|
||||
static void printer_moto_delay(uint32_t n)
|
||||
{
|
||||
volatile uint32_t i=500*n;
|
||||
while(i--)
|
||||
{
|
||||
}
|
||||
}
|
||||
|
||||
static void printer_data_delay(uint32_t n)
|
||||
{
|
||||
volatile uint32_t i=n;
|
||||
|
||||
while(i--)
|
||||
{
|
||||
}
|
||||
}
|
||||
|
||||
static void printer_delay(uint32_t n)
|
||||
{
|
||||
volatile uint32_t i=20*n;
|
||||
while(i--)
|
||||
{
|
||||
}
|
||||
}
|
||||
|
||||
void printer_moto_enable(uint8_t en)
|
||||
{
|
||||
if(en)
|
||||
{
|
||||
gpio_set_val(MOTO_SLEEP_PIN,1);
|
||||
printer_moto_delay(20);
|
||||
}
|
||||
else
|
||||
{
|
||||
gpio_set_val(MOTO_SLEEP_PIN,0);
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
int32_t get_printer_tm(){
|
||||
uint32 vol = 0;
|
||||
printer_delay(100);
|
||||
hgadc_tm = (struct hgadc_v0*)dev_get(HG_ADC0_DEVID);
|
||||
adc_open((struct adc_device *)(hgadc_tm));
|
||||
adc_add_channel((struct adc_device *)hgadc_tm, PRINTER_TM_PIN);
|
||||
adc_get_value((struct adc_device *)hgadc_tm, PRINTER_TM_PIN, &vol);
|
||||
os_printf("temperature:%d\r\n",vol);
|
||||
return vol;
|
||||
}
|
||||
|
||||
uint8_t is_paper_insert(){
|
||||
return gpio_get_val(PRINTER_PSENSOR_PIN);
|
||||
}
|
||||
|
||||
void paper_io_init(){
|
||||
|
||||
gpio_iomap_output(MOTO_SLEEP_PIN,GPIO_IOMAP_OUTPUT);
|
||||
#if SPI_SEND_EN
|
||||
spi0_dev = (struct spi_device *)dev_get(HG_SPI0_DEVID);
|
||||
spi_ioctl(spi0_dev,SPI_CFG_SET_NONE_CS,1,0);
|
||||
spi_ioctl(spi0_dev,SPI_SET_LSB_FIRST,0,0);
|
||||
spi_ioctl(spi0_dev,SPI_KICK_DMA_EN,0,0);
|
||||
|
||||
spi_open(spi0_dev,SPI_CLK_FREQ,SPI_MASTER_MODE,SPI_WIRE_SINGLE_MODE,SPI_CPOL_0_CPHA_0);
|
||||
#else
|
||||
gpio_iomap_output(PRINTER_DATA_PIN,GPIO_IOMAP_OUTPUT);
|
||||
gpio_iomap_output(PRINTER_CLK_PIN,GPIO_IOMAP_OUTPUT);
|
||||
#endif
|
||||
|
||||
gpio_iomap_output(PRINTER_LATCH_PIN,GPIO_IOMAP_OUTPUT);
|
||||
gpio_set_val(PRINTER_LATCH_PIN,1);
|
||||
|
||||
gpio_iomap_output(PRINTER_STB_PIN,GPIO_IOMAP_OUTPUT);
|
||||
gpio_iomap_output(PRINTER_EN_PIN,GPIO_IOMAP_OUTPUT);
|
||||
|
||||
gpio_iomap_output(PRINTER_TM_PIN,GPIO_IOMAP_OUTPUT);
|
||||
|
||||
|
||||
gpio_set_mode(PRINTER_PSENSOR_PIN, GPIO_PULL_NONE, GPIO_PULL_LEVEL_NONE);
|
||||
gpio_iomap_input(PRINTER_PSENSOR_PIN,GPIO_IOMAP_INPUT);
|
||||
|
||||
/////////////pwm init//////////////
|
||||
gpio_iomap_output(MOTO_AIN1_PIN,GPIO_IOMAP_OUTPUT); //PWM_CHANNEL_0 a
|
||||
gpio_iomap_output(MOTO_AIN2_PIN,GPIO_IOMAP_OUTPUT); //PWM_CHANNEL_1 c
|
||||
gpio_iomap_output(MOTO_BIN1_PIN,GPIO_IOMAP_OUTPUT); //PWM_CHANNEL_2 b
|
||||
gpio_iomap_output(MOTO_BIN2_PIN,GPIO_IOMAP_OUTPUT); //PWM_CHANNEL_3 d
|
||||
|
||||
moto_hgpwm = (struct hgpwm_v0 *)dev_get(HG_PWM0_DEVID);
|
||||
|
||||
pwm_init((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_0, 1000, 1000);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_0, PWM_IOCTL_CMD_SET_PRESCALER, (uint32)0x7, 0); //配置分频比
|
||||
pwm_start((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_0);
|
||||
pwm_init((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_1, 1000, 1000);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_1, PWM_IOCTL_CMD_SET_PRESCALER, (uint32)0x7, 0); //配置分频比
|
||||
pwm_start((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_1);
|
||||
pwm_init((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_2, 1000, 1000);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_2, PWM_IOCTL_CMD_SET_PRESCALER, (uint32)0x7, 0); //配置分频比
|
||||
pwm_start((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_2);
|
||||
pwm_init((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_3, 1000, 1000);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_3, PWM_IOCTL_CMD_SET_PRESCALER, (uint32)0x7, 0); //配置分频比
|
||||
pwm_start((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_3);
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_init((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_4, STB_PIN_PWM_PERIOD, 0);
|
||||
pwm_start((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_4);
|
||||
#endif
|
||||
|
||||
}
|
||||
|
||||
void moto_pwm_start()
|
||||
{
|
||||
#if (HEAT_MOTO_SEPARATION && PRINTER_PWM_3_EN)
|
||||
pwm_start((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_0);
|
||||
pwm_start((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_1);
|
||||
pwm_start((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_2);
|
||||
pwm_start((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_3);
|
||||
#endif
|
||||
}
|
||||
|
||||
void moto_pwm_stop()
|
||||
{
|
||||
#if (HEAT_MOTO_SEPARATION && PRINTER_PWM_3_EN)
|
||||
pwm_stop((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_0);
|
||||
pwm_stop((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_1);
|
||||
pwm_stop((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_2);
|
||||
pwm_stop((struct pwm_device *)moto_hgpwm, PWM_CHANNEL_3);
|
||||
#endif
|
||||
}
|
||||
|
||||
void paper_io_deinit(){
|
||||
struct hgadc_v0* hgadc_tm;
|
||||
hgadc_tm = (struct hgadc_v0*)dev_get(HG_ADC0_DEVID);
|
||||
adc_close((struct adc_device *)(hgadc_tm));
|
||||
adc_delete_channel((struct adc_device *)(hgadc_tm),PRINTER_TM_PIN);
|
||||
pwm_deinit((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_0);
|
||||
pwm_deinit((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_1);
|
||||
pwm_deinit((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_2);
|
||||
pwm_deinit((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_3);
|
||||
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_deinit((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4);
|
||||
#endif
|
||||
|
||||
#if SPI_SEND_EN
|
||||
spi_close(spi0_dev);
|
||||
#endif
|
||||
}
|
||||
|
||||
void printer_mote_run(){
|
||||
uint32_t flags;
|
||||
flags = disable_irq();
|
||||
|
||||
#if PRINTER_PWM_1_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_3,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1086*24, 407*24);//MOTO_BIN2_PIN 1086 ==>13.9ms
|
||||
printer_delay(8285); //3.46ms
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_1,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1086*24, 407*24);//MOTO_AIN2_PIN
|
||||
printer_delay(8285);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_2,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1086*24, 407*24);//MOTO_BIN1_PIN
|
||||
printer_delay(8285);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_0,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1086*24, 407*24);//MOTO_AIN1_PIN
|
||||
#elif PRINTER_PWM_2_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_3,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1406*24, 527*24);//MOTO_BIN2_PIN 1406 ==>18.0ms
|
||||
printer_delay(10775); //4.5ms
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_1,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1406*24, 527*24);//MOTO_AIN2_PIN
|
||||
printer_delay(10775);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_2,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1406*24, 527*24);//MOTO_BIN1_PIN
|
||||
printer_delay(10775);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_0,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1406*24, 527*24);//MOTO_AIN1_PIN
|
||||
#elif PRINTER_PWM_3_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_3,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1875*24, 703*24);//MOTO_BIN2_PIN 1875 ==>24.0ms 4:1
|
||||
printer_delay(14367); //6ms
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_1,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1875*24, 703*24);//MOTO_AIN2_PIN
|
||||
printer_delay(14367);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_2,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1875*24, 703*24);//MOTO_BIN1_PIN
|
||||
printer_delay(14367);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_0,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 1875*24, 703*24);//MOTO_AIN1_PIN
|
||||
#elif PRINTER_PWM_4_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_3,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 2500*24, 938*24);//MOTO_BIN2_PIN 2500 ==>32.0ms 4:1
|
||||
printer_delay(19200); //8ms
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_1,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 2500*24, 938*24);//MOTO_AIN2_PIN
|
||||
printer_delay(19200);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_2,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 2500*24, 938*24);//MOTO_BIN1_PIN
|
||||
printer_delay(19200);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_0,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 2500*24, 938*24);//MOTO_AIN1_PIN
|
||||
|
||||
#endif
|
||||
enable_irq(flags);
|
||||
}
|
||||
|
||||
void printer_mote_stop(){
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_0,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 50, 0);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_1,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 50, 0);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_2,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 50, 0);
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_3,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, 50, 0);
|
||||
}
|
||||
|
||||
|
||||
bool timer7_noisr_func(){
|
||||
#define HOTTIME 900
|
||||
uint32_t itk = 0;
|
||||
uint32_t jtk = 0;
|
||||
static uint32_t i = 0;
|
||||
static uint32_t j = 0;
|
||||
static uint32_t tick = 0;
|
||||
static uint32_t hot_time = 0;
|
||||
static uint32_t grep_step = 0;
|
||||
static uint8_t half_s = 0;
|
||||
static uint8_t hot_add = 0;
|
||||
uint32 offset_h;
|
||||
uint8_t *pt;
|
||||
pt = printer_buf;
|
||||
if(printer_h == 0){
|
||||
tick = 0;
|
||||
printer_h = 1;
|
||||
grep_step = 0;
|
||||
}
|
||||
offset_h = (printer_h-1)*PRINTER_W;
|
||||
|
||||
#if SPI_SEND_EN
|
||||
|
||||
if((tick%2) == 0){
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, STB_PIN_PWM_PERIOD, STB_PIN_PWM_DUTY);
|
||||
#else
|
||||
PRINTER_STB_PORT->ODAT |= BIT(PRINTER_STB_NUM);
|
||||
#endif
|
||||
|
||||
#if 1
|
||||
if(hot_time > HOTTIME)
|
||||
goto deal_end;
|
||||
#endif
|
||||
|
||||
if(half_s){
|
||||
|
||||
//偶数点
|
||||
spi_ioctl((struct spi_device*)spi0_dev, SPI_KICK_DMA_TX, (uint32)&printer_buf_even, 48);
|
||||
|
||||
#if PRINTER_PWM_4_EN
|
||||
for(jtk = 0; jtk < 48; jtk++)
|
||||
{
|
||||
for(itk = 1 + i; itk < 8; itk+=4)
|
||||
{
|
||||
if((pt[offset_h+jtk*8+itk]) > 0 && (1)){
|
||||
pt[offset_h+jtk*8+itk]--;
|
||||
printer_buf_odd[jtk] |= (0x1 << (7-itk));
|
||||
}
|
||||
}
|
||||
}
|
||||
if(i == 2)
|
||||
i = 0;
|
||||
else
|
||||
i = 2;
|
||||
#else
|
||||
for(jtk = 0; jtk < 48; jtk++)
|
||||
{
|
||||
for(itk = 1 + i; itk < 8; itk+=2)
|
||||
{
|
||||
if((pt[offset_h+jtk*8+itk]) > 0 && (1)){
|
||||
pt[offset_h+jtk*8+itk]--;
|
||||
printer_buf_odd[jtk] |= (0x1 << (7-itk));
|
||||
}
|
||||
}
|
||||
}
|
||||
#endif
|
||||
|
||||
} else {
|
||||
|
||||
//奇数点
|
||||
spi_ioctl((struct spi_device*)spi0_dev, SPI_KICK_DMA_TX, (uint32)&printer_buf_odd, 48);
|
||||
|
||||
#if PRINTER_PWM_4_EN
|
||||
for(jtk = 0; jtk < 48; jtk++)
|
||||
{
|
||||
for(itk = 0 + j; itk < 8; itk+=4)
|
||||
{
|
||||
if((pt[offset_h+jtk*8+itk]) > 0 && (1)){
|
||||
pt[offset_h+jtk*8+itk]--;
|
||||
printer_buf_even[jtk] |= (0x1 << (7-itk));
|
||||
}
|
||||
}
|
||||
}
|
||||
if(j == 2)
|
||||
j = 0;
|
||||
else
|
||||
j = 2;
|
||||
#else
|
||||
for(jtk = 0; jtk < 48; jtk++)
|
||||
{
|
||||
for(itk = 0 + j; itk < 8; itk+=2)
|
||||
{
|
||||
if((pt[offset_h+jtk*8+itk]) > 0 && (1)){
|
||||
pt[offset_h+jtk*8+itk]--;
|
||||
printer_buf_even[jtk] |= (0x1 << (7-itk));
|
||||
}
|
||||
}
|
||||
|
||||
}
|
||||
|
||||
#endif
|
||||
}
|
||||
|
||||
while(!spi_ioctl((struct spi_device*)spi0_dev, SPI_GET_DMA_PENDING, 0, 0));
|
||||
|
||||
spi_ioctl((struct spi_device*)spi0_dev, SPI_CLEAR_DMA_PENDING, 1, 0);
|
||||
|
||||
}
|
||||
else{
|
||||
#if PRINTER_PWM_3_EN
|
||||
#if !HEAT_MOTO_SEPARATION
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, STB_PIN_PWM_PERIOD, 0);
|
||||
#else
|
||||
PRINTER_STB_PORT->ODAT &= ~BIT(PRINTER_STB_NUM);
|
||||
#endif
|
||||
#endif
|
||||
#else
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, STB_PIN_PWM_PERIOD, 0);
|
||||
#else
|
||||
PRINTER_STB_PORT->ODAT &= ~BIT(PRINTER_STB_NUM);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if 1
|
||||
if(hot_time > HOTTIME)
|
||||
goto deal_end;
|
||||
#endif
|
||||
|
||||
if(half_s)
|
||||
memset(printer_buf_even, 0, 48);
|
||||
else
|
||||
memset(printer_buf_odd , 0, 48);
|
||||
|
||||
|
||||
gpio_set_val(PRINTER_LATCH_PIN,0);
|
||||
gpio_set_val(PRINTER_LATCH_PIN,1);
|
||||
|
||||
half_s ^= BIT(0);
|
||||
hot_add++;
|
||||
if((hot_add%2) == 0){
|
||||
grep_step++;
|
||||
}
|
||||
}
|
||||
|
||||
#else
|
||||
|
||||
if((tick%2) == 0){
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, STB_PIN_PWM_PERIOD, STB_PIN_PWM_DUTY);
|
||||
#else
|
||||
PRINTER_STB_PORT->ODAT |= BIT(PRINTER_STB_NUM);
|
||||
#endif
|
||||
|
||||
#if 1
|
||||
if(hot_time > HOTTIME)
|
||||
goto deal_end;
|
||||
#endif
|
||||
|
||||
|
||||
|
||||
if(half_s){
|
||||
for(itk = 0;itk < PRINTER_W;itk++){
|
||||
if(itk%2 == 0){ //偶数点
|
||||
if((pt[offset_h+itk]) > 0 && (1)){
|
||||
pt[offset_h+itk]--;
|
||||
PRINTER_DATA_PORT->ODAT |= BIT(PRINTER_DATA_NUM);
|
||||
}else{
|
||||
PRINTER_DATA_PORT->ODAT &= ~BIT(PRINTER_DATA_NUM);
|
||||
}
|
||||
} else { //奇数点
|
||||
PRINTER_DATA_PORT->ODAT &= ~BIT(PRINTER_DATA_NUM);
|
||||
}
|
||||
PRINTER_CLK_PORT->ODAT |= BIT(PRINTER_CLK_NUM);
|
||||
__NOP();__NOP();__NOP();__NOP();__NOP();__NOP(); //45 ns - 50 ns
|
||||
PRINTER_CLK_PORT->ODAT &= ~BIT(PRINTER_CLK_NUM);
|
||||
}
|
||||
}else{
|
||||
for(itk = 0;itk < PRINTER_W;itk++){
|
||||
if(itk%2 == 1){ //奇数点
|
||||
if((pt[offset_h+itk]) > 0 && (1)){
|
||||
pt[offset_h+itk]--;
|
||||
PRINTER_DATA_PORT->ODAT |= BIT(PRINTER_DATA_NUM);
|
||||
}else{
|
||||
PRINTER_DATA_PORT->ODAT &= ~BIT(PRINTER_DATA_NUM);
|
||||
}
|
||||
} else { //偶数点
|
||||
PRINTER_DATA_PORT->ODAT &= ~BIT(PRINTER_DATA_NUM);
|
||||
}
|
||||
PRINTER_CLK_PORT->ODAT |= BIT(PRINTER_CLK_NUM);
|
||||
__NOP();__NOP();__NOP();__NOP();__NOP();__NOP(); //45 ns - 50 ns
|
||||
PRINTER_CLK_PORT->ODAT &= ~BIT(PRINTER_CLK_NUM);
|
||||
}
|
||||
}
|
||||
}
|
||||
else{
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, STB_PIN_PWM_PERIOD, 0);
|
||||
#else
|
||||
PRINTER_STB_PORT->ODAT &= ~BIT(PRINTER_STB_NUM);
|
||||
#endif
|
||||
|
||||
#if 1
|
||||
if(hot_time > HOTTIME)
|
||||
goto deal_end;
|
||||
#endif
|
||||
|
||||
gpio_set_val(PRINTER_LATCH_PIN,0);
|
||||
gpio_set_val(PRINTER_LATCH_PIN,1);
|
||||
|
||||
half_s ^= BIT(0);
|
||||
hot_add++;
|
||||
if((hot_add%2) == 0){
|
||||
grep_step++;
|
||||
}
|
||||
}
|
||||
|
||||
#endif
|
||||
|
||||
deal_end:
|
||||
if((tick % TOTAL_TICK) == 0){
|
||||
printer_h++;
|
||||
hot_time = 0;
|
||||
grep_step = 0;
|
||||
#if (HEAT_MOTO_SEPARATION && PRINTER_PWM_3_EN)
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY, STB_PIN_PWM_PERIOD, 0);
|
||||
#else
|
||||
PRINTER_STB_PORT->ODAT &= ~BIT(PRINTER_STB_NUM);
|
||||
#endif
|
||||
moto_pwm_start();
|
||||
printer_delay(28734); //2x14367 16ms
|
||||
moto_pwm_stop();
|
||||
#endif
|
||||
if(printer_h == PRINTER_H){
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY,STB_PIN_PWM_PERIOD,0);
|
||||
#else
|
||||
PRINTER_STB_PORT->ODAT &= ~BIT(PRINTER_STB_NUM);
|
||||
#endif
|
||||
return 0;
|
||||
}
|
||||
}
|
||||
tick++;
|
||||
hot_time++;
|
||||
|
||||
return 1;
|
||||
}
|
||||
|
||||
/**
|
||||
* @brief 设置打印机的图片地址，赋值给全局变量printer_picture_addr
|
||||
*
|
||||
* @param addr 传入的图片地址
|
||||
* @return true
|
||||
* @return false
|
||||
*/
|
||||
bool printer_set_picture_addr(const unsigned char* addr)
|
||||
{
|
||||
if(addr == NULL) {
|
||||
os_printf("printer demo addr invaild!!! addr:%x\n",addr);
|
||||
return 1;
|
||||
}
|
||||
|
||||
printer_picture_addr = addr;
|
||||
|
||||
return 0;
|
||||
};
|
||||
|
||||
/**
|
||||
* @brief 切换打印机与摄像头的使能
|
||||
*
|
||||
* @param printer_en 如果使能打印机、关闭摄像头则置1，否则置0
|
||||
*/
|
||||
void printer_dvp_en_exchange(int printer_en)
|
||||
{
|
||||
|
||||
#if DVP_EN
|
||||
struct dvp_device *dvp_device = (struct dvp_device*)dev_get(HG_DVP_DEVID);
|
||||
struct vpp_device *vpp_device = (struct vpp_device*)dev_get(HG_VPP_DEVID);
|
||||
#endif
|
||||
|
||||
os_printf("%s %d\r\n",__FUNCTION__,printer_en);
|
||||
|
||||
//打印机使能
|
||||
if(printer_en)
|
||||
{
|
||||
gpio_set_val(PRINTER_EN_PIN,1);
|
||||
|
||||
#if DVP_EN
|
||||
gpio_iomap_output(PIN_DVP_PDN,GPIO_IOMAP_OUTPUT);
|
||||
gpio_set_val(PIN_DVP_PDN,1);
|
||||
dvp_close(dvp_device);
|
||||
vpp_close(vpp_device);
|
||||
|
||||
#endif
|
||||
}
|
||||
//DVP使能
|
||||
else {
|
||||
gpio_set_val(PRINTER_EN_PIN,0);
|
||||
|
||||
#if DVP_EN
|
||||
bool csi_ret;
|
||||
bool csi_cfg();
|
||||
bool csi_open();
|
||||
|
||||
gpio_iomap_output(PIN_DVP_PDN,GPIO_IOMAP_OUTPUT);
|
||||
gpio_set_val(PIN_DVP_PDN,0);
|
||||
#if SDH_I2C2_REUSE
|
||||
uint32 sdhost_i2c2_exchange(int sdh_stop_en);
|
||||
sdhost_i2c2_exchange(1);
|
||||
#endif
|
||||
csi_ret = csi_cfg();
|
||||
if(csi_ret)
|
||||
csi_open();
|
||||
//vpp_close(vpp_device);
|
||||
#if SDH_I2C2_REUSE
|
||||
sdhost_i2c2_exchange(0);
|
||||
#endif
|
||||
|
||||
#endif
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
void enhanceContrast(uint8_t *image) {
|
||||
int minLevel = 63;
|
||||
int maxLevel = 0;
|
||||
|
||||
for (int i = 0; i < PRINTER_W * PRINTER_H; i++) {
|
||||
if (image[i] < minLevel) {
|
||||
minLevel = image[i];
|
||||
}
|
||||
if (image[i] > maxLevel) {
|
||||
maxLevel = image[i];
|
||||
}
|
||||
}
|
||||
|
||||
int dynamicRange = maxLevel - minLevel;
|
||||
|
||||
for (int i = 0; i < PRINTER_W * PRINTER_H; i++) {
|
||||
image[i] = (image[i] - minLevel) * 63 / dynamicRange;
|
||||
|
||||
if (image[i] < 0) {
|
||||
image[i] = 0;
|
||||
}
|
||||
if (image[i] > 63) {
|
||||
image[i] = 63;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
unsigned char restrain_int(int input) {
|
||||
if (input < 0x00) {
|
||||
return 0x00;
|
||||
}
|
||||
|
||||
if (input > 0xFF) {
|
||||
return 0xFF;
|
||||
}
|
||||
|
||||
return input;
|
||||
}
|
||||
|
||||
//Floyd-Steinberg算法,该函数只适用于256灰阶图像
|
||||
void dithering(uint8_t *image, int width, int height) {
|
||||
// 对每个像素执行误差扩散
|
||||
for(int y = 0; y < height; y++) {
|
||||
for(int x = 0; x < width; x++) {
|
||||
int index = y * width + x;
|
||||
unsigned char oldPixel = image[index];
|
||||
unsigned char newPixel = (oldPixel < 128) ? 0 : 255; // 二值化
|
||||
|
||||
// 计算误差
|
||||
int error = oldPixel - newPixel;
|
||||
|
||||
// 更新当前像素
|
||||
image[index] = newPixel;
|
||||
|
||||
// 误差扩散到相邻像素
|
||||
if(x < width - 1) {
|
||||
image[index + 1] = restrain_int(image[index + 1] + (error * 7 / 16));
|
||||
}
|
||||
if(y < height - 1) {
|
||||
image[index + width] = restrain_int(image[index + width] + (error * 5 / 16));
|
||||
}
|
||||
if(x < width - 1 && y < height - 1) {
|
||||
image[index + width + 1] = restrain_int(image[index + width + 1] + (error * 1 / 16));
|
||||
}
|
||||
if(x > 0 && y < height - 1) {
|
||||
image[index + width - 1] = restrain_int(image[index + width - 1] + (error * 3 / 16));
|
||||
}
|
||||
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
extern volatile uint8 printer_action;
|
||||
extern uint8_t vga_room[2][640*480+640*480/2];
|
||||
bool printer_work(){
|
||||
uint32_t flags;
|
||||
uint8_t ret;
|
||||
#if !SPI_SEND_EN
|
||||
uint32_t print_w = PRINTER_W;
|
||||
#endif
|
||||
uint32_t itk = 0;
|
||||
uint32_t ktk = 0;
|
||||
uint32_t jtk = 0;
|
||||
int32_t tm;
|
||||
unsigned int grep_step = 0;
|
||||
os_sleep_ms(1000);
|
||||
|
||||
while(1){
|
||||
|
||||
if(printer_action == 0){
|
||||
os_sleep_ms(50);
|
||||
continue;
|
||||
}
|
||||
printer_action = 0;
|
||||
printer_h = 0;
|
||||
printf("-->Printer0 open!\r\n");
|
||||
paper_io_init(); //打印机IO初始化
|
||||
//gpio_set_val(PRINTER_EN_PIN,1); //enable printer power
|
||||
printer_dvp_en_exchange(1);
|
||||
printer_delay(500);
|
||||
printf("-->Printer0 open finish!\r\n");
|
||||
if(is_paper_insert()) // check paper
|
||||
{
|
||||
//gpio_set_val(PRINTER_EN_PIN,0); //disable printer power
|
||||
printer_dvp_en_exchange(0);
|
||||
printf("-->Printer error...no paper!!!\r\n");
|
||||
continue;
|
||||
}
|
||||
|
||||
tm = get_printer_tm(); //check tm
|
||||
if(1 == tm) // hot
|
||||
{
|
||||
//gpio_set_val(PRINTER_EN_PIN,0); //disable printer power
|
||||
printer_dvp_en_exchange(0);
|
||||
printf("-->Get the TM error...\r\n");
|
||||
continue;
|
||||
}
|
||||
|
||||
|
||||
memset(printer_buf,0,196608); //384 x 512
|
||||
#if 1
|
||||
dithering(vga_room, PRINTER_W, PRINTER_H); //半色调散点特效
|
||||
#endif
|
||||
//printer_set_picture_addr(printer_demo);
|
||||
printer_set_picture_addr(vga_room);
|
||||
for(itk = 0; itk < 512;itk++){ //384 x 512
|
||||
for(ktk = 0; ktk < 384;ktk++){
|
||||
grep_step = 0;
|
||||
for(jtk = 0;jtk < 64;jtk++){ //配置打印图片量化系数
|
||||
if(printer_picture_addr[itk*384+ktk] < (grep_step*4)/*255*/){ //64 4
|
||||
printer_buf[itk*384+383-ktk]++;
|
||||
}
|
||||
grep_step++;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
enhanceContrast(printer_buf);
|
||||
|
||||
|
||||
#if SPI_SEND_EN
|
||||
memset(printer_buf_even, 0, 48);
|
||||
memset(printer_buf_odd, 0, 48);
|
||||
|
||||
for(jtk = 0; jtk < 48; jtk++)
|
||||
{
|
||||
for(itk = 1; itk < 8; itk+=2)
|
||||
{
|
||||
if((printer_buf[jtk*8+itk]) > 0 && (1)){
|
||||
printer_buf[jtk*8+itk]--;
|
||||
printer_buf_odd[jtk] |= (1 << (7-itk));
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
#if SPI_SEND_EN
|
||||
flags = disable_irq();
|
||||
memset(printer_buf_even,0xFF,48);
|
||||
spi_ioctl((struct spi_device*)spi0_dev, SPI_KICK_DMA_TX, (uint32)&printer_buf_even, 48);
|
||||
while(!spi_ioctl((struct spi_device*)spi0_dev, SPI_GET_DMA_PENDING, 0, 0));
|
||||
spi_ioctl((struct spi_device*)spi0_dev, SPI_CLEAR_DMA_PENDING, 1, 0);
|
||||
enable_irq(flags);
|
||||
memset(printer_buf_even,0,48);
|
||||
#else
|
||||
for(itk = 0;itk < print_w;itk++){
|
||||
gpio_set_val(PRINTER_DATA_PIN,1);
|
||||
gpio_set_val(PRINTER_CLK_PIN,1);
|
||||
gpio_set_val(PRINTER_CLK_PIN,0);
|
||||
}
|
||||
#endif
|
||||
gpio_set_val(PRINTER_LATCH_PIN,0);
|
||||
gpio_set_val(PRINTER_LATCH_PIN,1);
|
||||
|
||||
|
||||
flags = disable_irq();
|
||||
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY,STB_PIN_PWM_PERIOD,STB_PIN_PWM_DUTY);
|
||||
#else
|
||||
gpio_set_val(PRINTER_STB_PIN,1); //预加热
|
||||
#endif
|
||||
|
||||
printer_delay(70000); // 25ms
|
||||
|
||||
enable_irq(flags);
|
||||
|
||||
|
||||
#if STB_PIN_PWM_EN
|
||||
pwm_ioctl((struct pwm_device *)moto_hgpwm,PWM_CHANNEL_4,PWM_IOCTL_CMD_SET_PERIOD_DUTY_IMMEDIATELY,STB_PIN_PWM_PERIOD,0);
|
||||
#else
|
||||
gpio_set_val(PRINTER_STB_PIN,0);
|
||||
#endif
|
||||
|
||||
mcu_watchdog_timeout(0);
|
||||
|
||||
|
||||
flags = disable_irq();
|
||||
printer_moto_enable(1);
|
||||
printer_mote_run();
|
||||
moto_pwm_stop();
|
||||
while(1){
|
||||
printer_delay(DELAY_NOHEAT); // 2.39个delay = 1us
|
||||
ret = timer7_noisr_func();
|
||||
if(ret == 0)
|
||||
break;
|
||||
printer_delay(DELAY_HEAT);
|
||||
ret = timer7_noisr_func();
|
||||
if(ret == 0)
|
||||
break;
|
||||
}
|
||||
enable_irq(flags);
|
||||
|
||||
mcu_watchdog_timeout(5);
|
||||
|
||||
moto_pwm_start();
|
||||
printer_delay(1000000);
|
||||
moto_pwm_stop();
|
||||
//gpio_set_val(PRINTER_EN_PIN,0); //disable printer power
|
||||
|
||||
paper_io_deinit();
|
||||
printer_dvp_en_exchange(0);
|
||||
printer_mote_stop();
|
||||
|
||||
|
||||
|
||||
printf("printer stop....\r\n");
|
||||
|
||||
}
|
||||
|
||||
}
|
||||
|
||||
void printer_thread_init(){
|
||||
OS_TASK_INIT("handle_printer", &handle_printer_task, printer_work, NULL, OS_TASK_PRIORITY_NORMAL, 1024);
|
||||
}
|
||||
|
||||
#endif
|
||||
Reference in New Issue
Block a user