Delete AccDec_17LED_6Ftn.ino
This commit is contained in:
Geoff Bunza
GitHub
@@ -1,484 +0,0 @@
|
||||
// Production 17 Switch Acessory DCC Decoder AccDec_17LED_6Ftn.ino
|
||||
// Version 6.0 Geoff Bunza 2014,2015,2016,2017,2018
|
||||
// Now works with both short and long DCC Addesses for CV Control Default 24 (LSB CV 121 ; MSB CV 122)
|
||||
// ACCESSORY DECODER DEFAULT ADDRESS IS 40 (MAX 40-56 SWITCHES)
|
||||
// ACCESSRY DECODER ADDRESS CAN NOW BE SET ABOVE 255
|
||||
// BE CAREFUL! DIFFERENT DCC BASE STATIONS ALLOW DIFFERING MAX ADDRESSES
|
||||
|
||||
// NO LONGER REQUIRES modified software servo Lib
|
||||
// Software restructuring mods added from Alex Shepherd and Franz-Peter
|
||||
// With sincere thanks
|
||||
|
||||
// ******** UNLESS YOU WANT ALL CV'S RESET UPON EVERY POWER UP
|
||||
// ******** AFTER THE INITIAL DECODER LOAD REMOVE THE "//" IN THE FOOLOWING LINE!!
|
||||
//#define DECODER_LOADED
|
||||
|
||||
// ******** REMOVE THE "//" IN THE FOOLOWING LINE TO SEND DEBUGGING
|
||||
// ******** INFO TO THE SERIAL MONITOR
|
||||
//#define DEBUG
|
||||
|
||||
#include <NmraDcc.h>
|
||||
#include <SoftwareServo.h>
|
||||
|
||||
SoftwareServo servo[17];
|
||||
#define servo_start_delay 50
|
||||
#define servo_init_delay 7
|
||||
#define servo_slowdown 12 //servo loop counter limit
|
||||
int servo_slow_counter = 0; //servo loop counter to slowdown servo transit
|
||||
|
||||
int tim_delay = 500;
|
||||
int numfpins = 17;
|
||||
byte fpins [] = {3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19};
|
||||
const int FunctionPin0 = 3;
|
||||
const int FunctionPin1 = 4;
|
||||
const int FunctionPin2 = 5;
|
||||
const int FunctionPin3 = 6;
|
||||
const int FunctionPin4 = 7;
|
||||
const int FunctionPin5 = 8;
|
||||
const int FunctionPin6 = 9;
|
||||
const int FunctionPin7 = 10;
|
||||
const int FunctionPin8 = 11;
|
||||
const int FunctionPin9 = 12;
|
||||
const int FunctionPin10 = 13;
|
||||
const int FunctionPin11 = 14; //A0
|
||||
const int FunctionPin12 = 15; //A1
|
||||
const int FunctionPin13 = 16; //A2
|
||||
const int FunctionPin14 = 17; //A3
|
||||
const int FunctionPin15 = 18; //A4
|
||||
const int FunctionPin16 = 19; //A5
|
||||
NmraDcc Dcc ;
|
||||
DCC_MSG Packet ;
|
||||
|
||||
int t; // temp
|
||||
#define SET_CV_Address 24 // THIS ADDRESS IS FOR SETTING CV'S Like a Loco
|
||||
#define Accessory_Address 40 // THIS ADDRESS IS THE START OF THE SWITCHES RANGE
|
||||
// WHICH WILL EXTEND FOR 16 MORE SWITCH ADDRESSES
|
||||
// THIS CAN START ABOVE ADDRESS 256
|
||||
uint8_t CV_DECODER_MASTER_RESET = 120; // THIS IS THE CV ADDRESS OF THE FULL RESET
|
||||
#define CV_To_Store_SET_CV_Address 121
|
||||
#define CV_Accessory_Address CV_ACCESSORY_DECODER_ADDRESS_LSB
|
||||
|
||||
struct QUEUE
|
||||
{
|
||||
int inuse;
|
||||
int current_position;
|
||||
int increment;
|
||||
int stop_value;
|
||||
int start_value;
|
||||
};
|
||||
QUEUE *ftn_queue = new QUEUE[17];
|
||||
|
||||
struct CVPair
|
||||
{
|
||||
uint16_t CV;
|
||||
uint8_t Value;
|
||||
};
|
||||
CVPair FactoryDefaultCVs [] =
|
||||
{
|
||||
// These two CVs define the Long Accessory Address
|
||||
{CV_ACCESSORY_DECODER_ADDRESS_LSB, Accessory_Address&0xFF},
|
||||
{CV_ACCESSORY_DECODER_ADDRESS_MSB, (Accessory_Address>>8)&0x07},
|
||||
|
||||
{CV_MULTIFUNCTION_EXTENDED_ADDRESS_MSB, 0},
|
||||
{CV_MULTIFUNCTION_EXTENDED_ADDRESS_LSB, 0},
|
||||
// Speed Steps don't matter for this decoder
|
||||
// ONLY uncomment 1 CV_29_CONFIG line below as approprate DEFAULT IS SHORT ADDRESS
|
||||
// {CV_29_CONFIG, 0}, // Short Address 14 Speed Steps
|
||||
{CV_29_CONFIG, CV29_F0_LOCATION}, // Short Address 28/128 Speed Steps
|
||||
// {CV_29_CONFIG, CV29_EXT_ADDRESSING | CV29_F0_LOCATION}, // Long Address 28/128 Speed Steps
|
||||
|
||||
{CV_DECODER_MASTER_RESET, 0},
|
||||
{CV_To_Store_SET_CV_Address, SET_CV_Address&0xFF }, // LSB Set CV Address
|
||||
{CV_To_Store_SET_CV_Address+1,(SET_CV_Address>>8)&0x3F }, //MSB Set CV Address
|
||||
{30, 0}, //F0 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{31, 1}, //F0 Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{32, 28}, //F0 Start Position F0=0
|
||||
{33, 140}, //F0 End Position F0=1
|
||||
{34, 28}, //F0 Current Position
|
||||
{35, 0}, //F1 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{36, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{37, 28}, // Start Position Fx=0
|
||||
{38, 140}, // End Position Fx=1
|
||||
{39, 28}, // Current Position
|
||||
{40, 0}, //F2 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{41, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{42, 28}, // Start Position Fx=0
|
||||
{43, 140}, // End Position Fx=1
|
||||
{44, 28}, // Current Position
|
||||
{45, 0}, //F3 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{46, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{47, 28}, // Start Position Fx=0
|
||||
{48, 140}, // End Position Fx=1
|
||||
{49, 28}, // Current Position
|
||||
{50, 0}, //F4 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{51, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{52, 28}, // Start Position Fx=0
|
||||
{53, 140}, // End Position Fx=1
|
||||
{54, 28}, // Current Position
|
||||
{55, 0}, //F5 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{56, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{57, 28}, // Start Position Fx=0
|
||||
{58, 140}, // End Position Fx=1
|
||||
{59, 28}, // Current Position
|
||||
{60, 0}, //F6 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{61, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{62, 28}, // Start Position Fx=0
|
||||
{63, 140}, // End Position Fx=1
|
||||
{64, 28}, // Current Position
|
||||
{65, 0}, //F7 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{66, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{67, 1}, // Start Position Fx=0
|
||||
{68,35}, // End Position Fx=1
|
||||
{69, 1}, // Current Position
|
||||
{70, 0}, //F8 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{71, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{72, 1}, // Start Position Fx=0
|
||||
{73, 100}, // End Position Fx=1
|
||||
{74, 1}, // Current Position
|
||||
{75, 0}, //F9 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{76, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{77, 1}, // Start Position Fx=0
|
||||
{78, 10}, // End Position Fx=1
|
||||
{79, 1}, // Current Position
|
||||
{80, 0}, //F10 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{81, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{82, 1}, // Start Position Fx=0
|
||||
{83, 5}, // End Position Fx=1
|
||||
{84, 1}, // Current Position
|
||||
{85, 1}, //F11 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{86, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{87, 1}, // Start Position Fx=0
|
||||
{88, 50}, // End Position Fx=1
|
||||
{89, 1}, // Current Position
|
||||
{90, 1}, //F12 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{91, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{92, 1}, // Start Position Fx=0
|
||||
{93, 100}, // End Position Fx=1
|
||||
{94, 1}, // Current Position
|
||||
{95, 3}, //F13 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{96, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{97, 1}, // Start Position Fx=0
|
||||
{98, 200}, // End Position Fx=1
|
||||
{99, 2}, // Current Position
|
||||
{100, 0}, //F14 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{101, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{102, 1}, // Start Position Fx=0
|
||||
{103, 200}, // End Position Fx=1
|
||||
{104, 1}, // Current Position
|
||||
{105, 3}, //F15 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{106, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{107, 1}, // Start Position Fx=0
|
||||
{108, 60}, // End Position Fx=1
|
||||
{109, 1}, // Current Position
|
||||
{110, 0}, //F16 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{111, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{112, 1}, // Start Position Fx=0
|
||||
{113, 4}, // End Position Fx=1
|
||||
{114, 1}, // Current Position
|
||||
//FUTURE USE
|
||||
{115, 0}, //F17 Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
{116, 1}, // Rate Blink=Eate,PWM=Rate,Servo=Rate
|
||||
{117, 28}, // Start Position Fx=0
|
||||
{118, 50}, // End Position Fx=1
|
||||
{119, 28}, // Current Position
|
||||
};
|
||||
uint8_t FactoryDefaultCVIndex = sizeof(FactoryDefaultCVs)/sizeof(CVPair);
|
||||
void notifyCVResetFactoryDefault()
|
||||
{
|
||||
// Make FactoryDefaultCVIndex non-zero and equal to num CV's to be reset
|
||||
// to flag to the loop() function that a reset to Factory Defaults needs to be done
|
||||
FactoryDefaultCVIndex = sizeof(FactoryDefaultCVs)/sizeof(CVPair);
|
||||
};
|
||||
|
||||
// NOTE: NO PROGRAMMING ACK IS SET UP TO MAXIMAIZE
|
||||
// OUTPUT PINS FOR FUNCTIONS
|
||||
|
||||
void setup() //******************************************************
|
||||
{
|
||||
#ifdef DEBUG
|
||||
Serial.begin(115200);
|
||||
#endif
|
||||
int i;
|
||||
uint8_t cv_value;
|
||||
// initialize the digital pins as outputs
|
||||
for (int i=0; i < numfpins; i++) {
|
||||
pinMode(fpins[i], OUTPUT);
|
||||
digitalWrite(fpins[i], 0);
|
||||
}
|
||||
for (int i=0; i < numfpins; i++) {
|
||||
digitalWrite(fpins[i], 1);
|
||||
delay (tim_delay/10);
|
||||
}
|
||||
delay( tim_delay);
|
||||
for (int i=0; i < numfpins; i++) {
|
||||
digitalWrite(fpins[i], 0);
|
||||
delay (tim_delay/10);
|
||||
}
|
||||
delay( tim_delay);
|
||||
|
||||
// Setup which External Interrupt, the Pin it's associated with that we're using
|
||||
Dcc.pin(0, 2, 0);
|
||||
// Call the main DCC Init function to enable the DCC Receiver
|
||||
Dcc.init( MAN_ID_DIY, 600, FLAGS_OUTPUT_ADDRESS_MODE | FLAGS_DCC_ACCESSORY_DECODER, CV_To_Store_SET_CV_Address);
|
||||
delay(800);
|
||||
|
||||
#if defined(DECODER_LOADED)
|
||||
if ( Dcc.getCV(CV_DECODER_MASTER_RESET)== CV_DECODER_MASTER_RESET )
|
||||
#endif
|
||||
|
||||
{
|
||||
for (int j=0; j < sizeof(FactoryDefaultCVs)/sizeof(CVPair); j++ )
|
||||
Dcc.setCV( FactoryDefaultCVs[j].CV, FactoryDefaultCVs[j].Value);
|
||||
digitalWrite(fpins[14], 1);
|
||||
delay (1000);
|
||||
digitalWrite(fpins[14], 0);
|
||||
}
|
||||
for ( i=0; i < numfpins; i++) {
|
||||
cv_value = Dcc.getCV( 30+(i*5)) ;
|
||||
#ifdef DEBUG
|
||||
Serial.print(" cv_value: ");
|
||||
Serial.println(cv_value, DEC) ;
|
||||
#endif
|
||||
switch ( cv_value ) {
|
||||
case 0: // LED on/off
|
||||
ftn_queue[i].inuse = 0;
|
||||
break;
|
||||
case 1: // LED Blink
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].start_value = 0;
|
||||
ftn_queue[i].increment = int (char (Dcc.getCV( 31+(i*5))));
|
||||
digitalWrite(fpins[i], 0);
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5))) ;
|
||||
}
|
||||
break;
|
||||
case 2: //servo
|
||||
{
|
||||
ftn_queue[i].current_position =int (Dcc.getCV( 34+(i*5)));
|
||||
ftn_queue[i].stop_value = int (Dcc.getCV( 33+(i*5)));
|
||||
ftn_queue[i].start_value = int (Dcc.getCV( 32+(i*5)));
|
||||
ftn_queue[i].increment = -int (char (Dcc.getCV( 31+(i*5))));
|
||||
// attaches servo on pin to the servo object
|
||||
servo[i].attach(fpins[i]);
|
||||
|
||||
#ifdef DEBUG
|
||||
Serial.print("InitServo ID= ");
|
||||
Serial.println(i, DEC) ;
|
||||
#endif
|
||||
servo[i].write(ftn_queue[i].start_value);
|
||||
for (t=0; t<servo_start_delay; t++)
|
||||
{SoftwareServo::refresh();delay(servo_init_delay);}
|
||||
ftn_queue[i].inuse = 0;
|
||||
servo[i].detach();
|
||||
}
|
||||
break;
|
||||
case 3: // DOUBLE ALTERNATING LED Blink
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].start_value = 0;
|
||||
ftn_queue[i].increment = Dcc.getCV( 31+(i*5));
|
||||
digitalWrite(fpins[i], 0);
|
||||
digitalWrite(fpins[i+1], 0);
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5)));
|
||||
}
|
||||
break;
|
||||
case 4: // Simple Pulsed Output based on saved Rate =10*Rate in Milliseconds
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].increment = 10 * int (char (Dcc.getCV( 31+(i*5))));
|
||||
digitalWrite(fpins[i], 0);
|
||||
}
|
||||
break;
|
||||
case 5: // Fade On
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].start_value = 0;
|
||||
ftn_queue[i].increment = int (char (Dcc.getCV( 31+(i*5))));
|
||||
digitalWrite(fpins[i], 0);
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5))) *10.;
|
||||
}
|
||||
break;
|
||||
case 6: // NEXT FEATURE to pin
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
void loop() //**********************************************************************
|
||||
{
|
||||
//MUST call the NmraDcc.process() method frequently
|
||||
// from the Arduino loop() function for correct library operation
|
||||
Dcc.process();
|
||||
SoftwareServo::refresh();
|
||||
delay(3);
|
||||
for (int i=0; i < numfpins; i++) {
|
||||
if (ftn_queue[i].inuse==1) {
|
||||
|
||||
switch (Dcc.getCV( 30+(i*5))) {
|
||||
case 0:
|
||||
break;
|
||||
case 1:
|
||||
ftn_queue[i].current_position = ftn_queue[i].current_position + ftn_queue[i].increment;
|
||||
if (ftn_queue[i].current_position > ftn_queue[i].stop_value) {
|
||||
ftn_queue[i].start_value = ~ftn_queue[i].start_value;
|
||||
digitalWrite(fpins[i], ftn_queue[i].start_value);
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5)));
|
||||
}
|
||||
break;
|
||||
case 2:
|
||||
{
|
||||
if (servo_slow_counter++ > servo_slowdown)
|
||||
{
|
||||
ftn_queue[i].current_position = ftn_queue[i].current_position + ftn_queue[i].increment;
|
||||
if (ftn_queue[i].increment > 0) {
|
||||
if (ftn_queue[i].current_position > ftn_queue[i].stop_value) {
|
||||
ftn_queue[i].current_position = ftn_queue[i].stop_value;
|
||||
ftn_queue[i].inuse = 0;
|
||||
servo[i].detach();
|
||||
}
|
||||
}
|
||||
if (ftn_queue[i].increment < 0) {
|
||||
if (ftn_queue[i].current_position < ftn_queue[i].start_value) {
|
||||
ftn_queue[i].current_position = ftn_queue[i].start_value;
|
||||
ftn_queue[i].inuse = 0;
|
||||
servo[i].detach();
|
||||
}
|
||||
}
|
||||
servo[i].write(ftn_queue[i].current_position);
|
||||
servo_slow_counter = 0;
|
||||
}
|
||||
}
|
||||
break;
|
||||
case 3:
|
||||
ftn_queue[i].current_position = ftn_queue[i].current_position + ftn_queue[i].increment;
|
||||
if (ftn_queue[i].current_position > ftn_queue[i].stop_value) {
|
||||
ftn_queue[i].start_value = ~ftn_queue[i].start_value;
|
||||
digitalWrite(fpins[i], ftn_queue[i].start_value);
|
||||
digitalWrite(fpins[i]+1, ~ftn_queue[i].start_value);
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].stop_value = int(Dcc.getCV( 33+(i*5)));
|
||||
}
|
||||
i++;
|
||||
break;
|
||||
case 4: // Simple Pulsed Output based on saved Rate =10*Rate in Milliseconds
|
||||
{
|
||||
ftn_queue[i].inuse = 0;
|
||||
ftn_queue[i].current_position = 0;
|
||||
ftn_queue[i].increment = 10 * int (char (Dcc.getCV( 31+(i*5))));
|
||||
digitalWrite(fpins[i], 0);
|
||||
}
|
||||
break;
|
||||
case 5: // Fade On
|
||||
|
||||
break;
|
||||
case 6: // NEXT FEATURE to pin
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
extern void notifyDccAccTurnoutOutput( uint16_t Addr, uint8_t Direction, uint8_t OutputPower ) {
|
||||
uint16_t Current_Decoder_Addr = Dcc.getAddr();
|
||||
|
||||
if ( Addr >= Current_Decoder_Addr && Addr < Current_Decoder_Addr+17) { //Controls Accessory_Address+16
|
||||
#ifdef DEBUG
|
||||
Serial.print("Addr = ");
|
||||
Serial.println(Addr);
|
||||
Serial.print("Direction = ");
|
||||
Serial.println(Direction);
|
||||
#endif
|
||||
exec_function(Addr-Current_Decoder_Addr, Direction );
|
||||
}
|
||||
}
|
||||
|
||||
void exec_function (int function, int FuncState) {
|
||||
byte pin;
|
||||
int servo_temp;
|
||||
pin = fpins[function];
|
||||
switch ( Dcc.getCV( 30+(function*5)) ) { // Config 0=On/Off,1=Blink,2=Servo,3=DBL LED Blink,4=Pulsed,5=fade
|
||||
case 0: // On - Off LED
|
||||
digitalWrite (pin, FuncState);
|
||||
ftn_queue[function].inuse = 0;
|
||||
break;
|
||||
case 1: // Blinking LED
|
||||
if ((ftn_queue[function].inuse==0) && (FuncState==1)) {
|
||||
ftn_queue[function].inuse = 1;
|
||||
ftn_queue[function].start_value = 0;
|
||||
digitalWrite(pin, 0);
|
||||
ftn_queue[function].stop_value = int(Dcc.getCV( 33+(function*5)));
|
||||
} else {
|
||||
if ((ftn_queue[function].inuse==1) && (FuncState==0)) {
|
||||
ftn_queue[function].inuse = 0;
|
||||
digitalWrite(pin, 0);
|
||||
}
|
||||
}
|
||||
break;
|
||||
case 2: // Servo
|
||||
if (ftn_queue[function].inuse == 0) {
|
||||
ftn_queue[function].inuse = 1;
|
||||
servo[function].attach(pin);
|
||||
}
|
||||
if (FuncState==1) ftn_queue[function].increment = char ( Dcc.getCV( 31+(function*5)));
|
||||
else ftn_queue[function].increment = - char(Dcc.getCV( 31+(function*5)));
|
||||
if (FuncState==1) ftn_queue[function].stop_value = Dcc.getCV( 33+(function*5));
|
||||
else ftn_queue[function].stop_value = Dcc.getCV( 32+(function*5));
|
||||
break;
|
||||
case 3: // Blinking LED PAIR
|
||||
if ((ftn_queue[function].inuse==0) && (FuncState==1)) {
|
||||
ftn_queue[function].inuse = 1;
|
||||
ftn_queue[function].start_value = 0;
|
||||
digitalWrite(fpins[function], 0);
|
||||
digitalWrite(fpins[function+1], 1);
|
||||
ftn_queue[function].stop_value = int(Dcc.getCV( 33+(function*5)));
|
||||
} else {
|
||||
if (FuncState==0) {
|
||||
ftn_queue[function].inuse = 0;
|
||||
digitalWrite(fpins[function], 0);
|
||||
digitalWrite(fpins[function+1], 0);
|
||||
}
|
||||
}
|
||||
break;
|
||||
case 4: // Pulse Output based on Rate*10 Milliseconds
|
||||
if ((ftn_queue[function].inuse==0) && (FuncState==1)) { //First Turn On Detected
|
||||
digitalWrite(fpins[function], 1);
|
||||
delay (10*ftn_queue[function].increment);
|
||||
digitalWrite(fpins[function], 0);
|
||||
ftn_queue[function].inuse = 1; //inuse set to 1 says we already pulsed
|
||||
} else
|
||||
if (FuncState==0) ftn_queue[function].inuse = 0;
|
||||
break;
|
||||
case 5: // Fade On
|
||||
#define fadedelay 24
|
||||
if ((ftn_queue[function].inuse==0) && (FuncState==1)) {
|
||||
ftn_queue[function].inuse = 1;
|
||||
for (t=0; t<ftn_queue[function].stop_value; t+=ftn_queue[function].increment) {
|
||||
digitalWrite( fpins[function], 1);
|
||||
delay(fadedelay*(t/(1.*ftn_queue[function].stop_value)));
|
||||
digitalWrite( fpins[function], 0);
|
||||
delay(fadedelay-(fadedelay*(t/(1.*ftn_queue[function].stop_value))));
|
||||
}
|
||||
digitalWrite( fpins[function], 1 );
|
||||
} else {
|
||||
if ((ftn_queue[function].inuse==1) && (FuncState==0)) {
|
||||
ftn_queue[function].inuse = 0;
|
||||
digitalWrite(fpins[function], 0);
|
||||
}
|
||||
}
|
||||
break;
|
||||
case 6: // Future Function
|
||||
ftn_queue[function].inuse = 0;
|
||||
break;
|
||||
default:
|
||||
ftn_queue[function].inuse = 0;
|
||||
break;
|
||||
}
|
||||
}
|
||||
Reference in New Issue
Block a user