Maison/ESP32/DCC-Bench/include/DCCGenerator.h

/**
 * @file DCCGenerator.h
 * @brief NMRA DCC (Digital Command Control) signal generator
 * 
 * Generates DCC protocol signals for controlling digital model locomotives.
 * Implements NMRA DCC standard with support for:
 * - Short addresses (1-127) and long addresses (128-10239)
 * - 128-step speed control
 * - Function control (F0-F12 implemented, expandable to F28)
 * 
 * @note Requires external DCC booster circuit for track output
 * @author Locomotive Test Bench Project
 * @date 2025
 */

#ifndef DCC_GENERATOR_H
#define DCC_GENERATOR_H

#include <Arduino.h>

// Pin definitions for DCC output
// These share the same pins as the motor controller (LM18200)
// In DCC mode: GPIO 18 = DCC Signal A, GPIO 19 = DCC Signal B
// In DC mode:  GPIO 18 = PWM, GPIO 19 = Direction
#define DCC_PIN_A 18    ///< DCC Signal A output pin (shared with MOTOR_PWM_PIN)
#define DCC_PIN_B 19    ///< DCC Signal B output pin (shared with MOTOR_DIR_PIN)

// DCC timing constants (microseconds) - NMRA standard
#define DCC_ONE_BIT_TOTAL_DURATION_MAX 64     ///< Max duration for '1' bit
#define DCC_ONE_BIT_TOTAL_DURATION_MIN 55     ///< Min duration for '1' bit
#define DCC_ZERO_BIT_TOTAL_DURATION_MAX 10000 ///< Max duration for '0' bit
#define DCC_ZERO_BIT_TOTAL_DURATION_MIN 95    ///< Min duration for '0' bit

#define DCC_ONE_BIT_PULSE_DURATION 58   ///< Half-cycle for '1' bit (58μs)
#define DCC_ZERO_BIT_PULSE_DURATION 100 ///< Half-cycle for '0' bit (100μs)

/**
 * @class DCCGenerator
 * @brief DCC protocol signal generator
 * 
 * Generates NMRA-compliant DCC signals for digital locomotive control.
 * Supports variable speed, direction, and function commands.
 * 
 * @warning Output signals are low-power logic level.
 * Requires external booster circuit for track connection.
 */
class DCCGenerator {
public:
    /**
     * @brief Constructor
     */
    DCCGenerator();
    
    /**
     * @brief Initialize DCC generator hardware
     * 
     * Configures output pins to idle state.
     */
    void begin();
    
    /**
     * @brief Enable DCC signal generation
     * 
     * Starts sending DCC packets to the track.
     */
    void enable();
    
    /**
     * @brief Disable DCC signal generation
     * 
     * Stops DCC output and sets pins to safe state.
     */
    void disable();
    
    /**
     * @brief Set locomotive speed and direction
     * @param address DCC address (1-10239)
     * @param speed Speed value (0-100%)
     * @param direction Direction: 0 = reverse, 1 = forward
     */
    void setLocoSpeed(uint16_t address, uint8_t speed, uint8_t direction);
    
    /**
     * @brief Control DCC function
     * @param address DCC address (1-10239)
     * @param function Function number (0-28)
     * @param state true = ON, false = OFF
     */
    void setFunction(uint16_t address, uint8_t function, bool state);
    
    /**
     * @brief Update DCC signal generation
     * 
     * Must be called regularly from main loop to send DCC packets.
     * Sends speed and function packets at appropriate intervals.
     */
    void update();
    
    /**
     * @brief Check if DCC is enabled
     * @return true if DCC mode is active
     */
    bool isEnabled() { return enabled; }
    
    // Programming Track Methods
    
    /**
     * @brief Factory reset decoder (send CV8 = 8)
     * @return true if successful
     */
    bool factoryReset();
    
    /**
     * @brief Set decoder address
     * @param address New address (1-10239)
     * @return true if successful
     */
    bool setDecoderAddress(uint16_t address);
    
    /**
     * @brief Read CV value from decoder
     * @param cv CV number (1-1024)
     * @param value Pointer to store read value
     * @return true if successful
     */
    bool readCV(uint16_t cv, uint8_t* value);
    
    /**
     * @brief Write CV value to decoder
     * @param cv CV number (1-1024)
     * @param value Value to write (0-255)
     * @return true if successful
     */
    bool writeCV(uint16_t cv, uint8_t value);
    
private:
    bool enabled;               ///< DCC generator enabled flag
    uint16_t currentAddress;    ///< Current locomotive address
    uint8_t currentSpeed;       ///< Current speed setting
    uint8_t currentDirection;   ///< Current direction (0=rev, 1=fwd)
    uint32_t functionStates;    ///< Function states bit field
    
    unsigned long lastPacketTime;  ///< Timestamp of last packet sent
    static const unsigned long PACKET_INTERVAL = 30; ///< Packet interval (ms)
    
    // DCC packet construction and transmission
    
    /**
     * @brief Send a complete DCC packet
     * @param data Byte array containing packet data
     * @param length Number of bytes in packet
     */
    void sendPacket(uint8_t* data, uint8_t length);
    
    /**
     * @brief Send a single DCC bit
     * @param value true = '1' bit, false = '0' bit
     */
    void sendBit(bool value);
    
    /**
     * @brief Send DCC preamble (14 '1' bits)
     */
    void sendPreamble();
    
    /**
     * @brief Send a single byte
     * @param data Byte to send
     */
    void sendByte(uint8_t data);
    
    /**
     * @brief Send speed command packet
     */
    void sendSpeedPacket();
    
    /**
     * @brief Send function group packet
     * @param group Function group number
     */
    void sendFunctionPacket(uint8_t group);
    
    /**
     * @brief Calculate XOR checksum
     * @param data Data bytes
     * @param length Number of bytes
     * @return XOR checksum byte
     */
    uint8_t calculateChecksum(uint8_t* data, uint8_t length);
    
    // Programming track helper methods
    
    /**
     * @brief Send service mode packet (programming track)
     * @param data Packet data bytes
     * @param length Number of bytes
     */
    void sendServiceModePacket(uint8_t* data, uint8_t length);
    
    /**
     * @brief Verify byte write on programming track
     * @param cv CV number
     * @param value Expected value
     * @return true if ACK detected
     */
    bool verifyByte(uint16_t cv, uint8_t value);
    
    /**
     * @brief Wait for ACK pulse from decoder
     * @return true if ACK detected within timeout
     */
    bool waitForAck();
    
    /**
     * @brief Calibrate ACS712 current sensor zero point
     * 
     * Reads current sensor with no load to establish baseline.
     * Should be called during initialization.
     */
    void calibrateCurrentSensor();
};

// Programming track current sensing threshold (mA)
#define PROG_ACK_CURRENT_THRESHOLD 60  ///< Minimum ACK current (mA)

#endif