Serge NOEL
98 lines
4.4 KiB
Python
98 lines
4.4 KiB
Python
# Script Programs DCC Specialties - BlockWatcher
|
|
# http://www.dccspecialties.com
|
|
#
|
|
# Script by Brett Scott
|
|
# Version 1.50 07/27/2014
|
|
# mgbrrclub@gmail.com or info@mgbrr.org and www.mgbrr.org
|
|
#
|
|
# Many Thanks to Bob Jacobsen and Everyone who Contributes to JMRI.
|
|
#
|
|
# Script should work for any DCC System that supports Ops Mode Programming or
|
|
# Programming on Mainline. (Digitrax, NEC, MRC, Lenz)
|
|
#
|
|
# You should copy this file to ProgramBlockWatcher????.py Replacing ????
|
|
# with the Primary Address of your BlockWatcher. You should keep this file
|
|
# for backup, and future tweaking and programming.
|
|
#
|
|
# Each group of program lines is documented. To execute a group of statements, remove
|
|
# the # from the beginning of the proceeding program lines. Edit the program lines
|
|
# to include necessary information for your BlockWatcher.
|
|
#
|
|
# Be Sure to remove the # from the "self.waitMsec(750)" line. This gives the BlockWatcher sufficient
|
|
# time to process each preceding command.
|
|
#
|
|
# This script uses Locomotive Address 9983. Please make sure there is NO Locomotive number 9983
|
|
# on your layout while running this script. This script will reprogram several of its CV's.
|
|
#
|
|
# Instructions
|
|
# 1. Turn Off Track Power - Use a Throttle or JMRI to do this.
|
|
# 2. Move the Program Jumper J3 from either [J3-2 J3-3] or [J3-3 J3-4] To [J3-1 J3-2](Program Mode)
|
|
# 3. Turn On Track Power - Again, Use a Throttle or JMRI.
|
|
# 4. VERY IMPORTANT - Wait 30 to 45 Seconds.
|
|
# 5. In JMRI DecoderPro, Go to Panels > Run Script. Select the file that corresponds
|
|
# to the BlockWatcher you are programming. Note - Do not have the file open in an editor.
|
|
#
|
|
# Important - This script can take 2 to 6 seconds to run. This depends on the number of
|
|
# CV's and addresses being programmed.
|
|
#
|
|
# When the script is complete, a small message window should appear. Usually
|
|
# in the upper left corner of your screen.
|
|
#
|
|
# 6. Turn Off Track Power.
|
|
# 7. Move the program jumper J3 from [J3-1 J3-2] back to [J2-2 J2-3](Automatic Setting Leakage Current)
|
|
# or [J3-3 J3-4](Leakage Current Set with CV).
|
|
# 8. Turn Track Power On.
|
|
# 9. Test you BlockWatcher.
|
|
#
|
|
|
|
import jmri
|
|
import javax.swing
|
|
|
|
class setStartup(jmri.jmrit.automat.AbstractAutomaton) :
|
|
def init(self):
|
|
return
|
|
|
|
def handle(self):
|
|
# Next Two Lines - Reset BlockWatcher to Factory Defaults
|
|
addressedProgrammers.getAddressedProgrammer(True, 9983).writeCV("63", 42, None)
|
|
self.waitMsec(750) # time is in milliseconds
|
|
|
|
# Next Two Lines - Point BlockWatcher to Receive Primary Address, Not Necessary, However, good practice.
|
|
addressedProgrammers.getAddressedProgrammer(True, 9983).writeCV("63", 0, None)
|
|
self.waitMsec(750)
|
|
|
|
# Next Two Lines - Set Primary Address - Change 1234 to Address Desired
|
|
turnouts.provideTurnout("1234").setState(CLOSED)
|
|
self.waitMsec(750)
|
|
|
|
# Last Two Lines of this Group - CV53 - Delay in Milliseconds
|
|
# Sets the delay in milliseconds that the block current exceeds the trip level
|
|
# before the J4 output will turn on. It is also the turn-off delay for the amount
|
|
# of time the block current is below the trip level before the J4 output turns
|
|
# off. The default value is 32 ms.
|
|
# addressedProgrammers.getAddressedProgrammer(True, 9983).writeCV("53", 32, None)
|
|
# self.waitMsec(750)
|
|
|
|
# Last Two Lines of this Group - CV54 - Average Unoccupied Block Current
|
|
# This CV sets the average value of the block current when it is unoccupied.
|
|
# The J4 turn on threshold is 3 + CV54 + CV55. The turn off threshold is 3 + CV54.
|
|
# The scaling value is 0.534 mA per bit. The default is 0, which will result in
|
|
# a trip current of about 2 mA. The maximum value is 254 � CV55 � 3.
|
|
# This sets the maximum trip current to about 130 mA.
|
|
# (With J3 on pins 2-3 this value is set each time power is applied to the detector.)
|
|
# addressedProgrammers.getAddressedProgrammer(True, 9983).writeCV("54", 0, None)
|
|
# self.waitMsec(750)
|
|
|
|
# Last Two Lines of this Group - CV55 - Hysterisis Between On and Off
|
|
# Sets the hysterisis between on and off (see CV54). Its default value is 1.
|
|
# This keeps the detector fromfluttering when the detected current is near the switching point.
|
|
# addressedProgrammers.getAddressedProgrammer(True, 9983).writeCV("55", 1, None)
|
|
# self.waitMsec(750)
|
|
|
|
javax.swing.JFrame("Programming Complete!").show()
|
|
|
|
return
|
|
|
|
setStartup().start()
|
|
|