Start voltage Volt Partenza V démarr. Startspannung A value of 255 corresponds to 100% Motor PWM Period Periodo PWM (Frequenza pilotaggio Motore) 52.2mS to 5.12 ms Packet Timeout Value Consist Address Active For F1 Consist Address Active For F2 Consist Address Active For F3 Consist Address Active For F4 Consist Address Active For F5 Consist Address Active For F6 Consist Address Active For F7 Consist Address Active For F8 Consist Address Active For FL in Forward Consist Address Active For FL in Reverse Consist Acceleration Rate Additional consist acceleration (combined with CV3) Consist Acceleration Sign Consist Braking Rate Additional consist braking (combined with CV4) Consist Braking Sign no table no table Straight Line Log Curve 1 Log Curve 2 Log Curve 3 Log Curve 4 Log Curve 5 Log Curve 6 Log Curve 7 Exp Curve 1 Exp Curve 2 Exp Curve 3 Exp Curve 4 Exp Curve 5 Exp Curve 6 User Table Speed Table Selection System Normal CV112-128 mapped to 49-65 CV Address Extension System Normal Data corrupted. Reset to defaults. EEROM Data Corrupted System Normal Ignore Group3 steerage bit Function Group 3 Disable NMRA function map Soundtraxx function map Alternate Function Map System Normal Watchdog timeout occurred Watchdog Timer Reset System Normal Checksum Test Failed Program Checksum Failure System Normal No ACK from I2C bus I2C Bus Acknowledge Failure FL(f) controls headlight FL(f) controls backup light FL(f) controls output Horn FL(f) controls output Bell FL(f) controls FX1 FL(f) controls FX2 FL(f) controls output DynBrake FL(r) controls headlight FL(r) controls backup light FL(r) controls output Horn FL(r) controls output Bell FL(r) controls FX1 FL(r) controls FX2 FL(r) controls output DynBrake F1 controls headlight F1 controls backup light F1 controls output Horn F1 controls output Bell F1 controls FX1 F1 controls FX2 F1 controls output DynBrake F2 controls headlight F2 controls backup light F2 controls output Horn F2 controls output Bell F2 controls FX1 F2 controls FX2 F2 controls output DynBrake F3 controls output Bell F3 controls FX1 F3 controls FX2 F3 controls output DynBrake F3 controls output RPM+ F3 controls output RPM- F3 controls output Dim F4 controls output Bell F4 controls FX1 F4 controls FX2 F4 controls output DynBrake F4 controls output RPM+ F4 controls output RPM- F4 controls output Dim F5 controls output Bell F5 controls FX1 F5 controls FX2 F5 controls output DynBrake F5 controls output RPM+ F5 controls output RPM- F5 controls output Dim F6 controls output Bell F6 controls FX1 F6 controls FX2 F6 controls output DynBrake F6 controls output RPM+ F6 controls output RPM- F6 controls output Dim F7 controls output DynBrake F7 controls output RPM+ F7 controls output RPM- F7 controls output Dim F7 controls output Mute F8 controls output DynBrake F8 controls output RPM+ F8 controls output RPM- F8 controls output Dim F8 controls output Mute On/Off Dimmable Forward light F0F effect generated directional Rule 17 enable Forward light F0F behavior On/Off Dimmable Reverse light F0R effect generated directional Rule 17 enable Reverse light F0R behavior Hyperlight flash rate 0 is fast, 15 is slow, 4 is recommended for start Grade crossing logic hold time 0-15 seconds On at power up On when loco selected Startup Mode Dynamic Digital Exhaust Single Chime Three Chime Five Chime Horn Select Engine RPM Interlock Bell Rate low values = fast, high values = slow Exhaust Auto Notching Control Number of speed steps per throttle notch. Airhorn Volume Bell Volume Exhaust Volume Dynamic Brake Volume Reset delle CV ai valori di fabbrica Soundtraxx