LOCONETCSOPSWMODE Two Jump Ports * One Jump Port The DCS5x throttle implements OpSw01 Command Station and Throttle and Booster* Booster and Throttle Device acts as a OpSw02 AutoReversing Mode is OpSw03 OpSw04 OpSw04 VMax, ThrottleID and Brake Rate changes are OpSw05 Latching (push-on, push-off)* Non-Latching (momentary) Function 3 is OpSw06 "Blast" Mode programming is Blast-mode programming on the service-mode programming track improves the ability to read and write some decoders OpSw08 OpSw08 OpSw09 OpSw09 OpSw10 OpSw10 OpSw11 OpSw11 addresses as defined in OpSw10 * up to 8 previously-used addresses OpSw 11 eq 0 2 previously-used addresses * 4 previously-used addresses DCS51 Throttle remembers OpSw10 and OpSw11 OpSw12 OpSw12 Command Station Slot "Purge" OpSw14 OpSw 14 eq 0 200 seconds * 600 seconds Command Station Slot "Purge" Time OpSw13 OpSw 14 eq 0 "Purge" forces loco speed to 0 OpSw15 OpSw16 OpSw16 Automatic Advanced Decoder-Assisted consisting is OpSw17 1/8 second * 1/2 second Short-Circuit Shutdown Time is OpSw18 OpSw19 OpSw19 Address 00 (Analog stretching) is OpSw20 Normal * Alternate Normal * Alternate Normal * Alternate Global System Loco "Speed-step Mode" Default for New Loco Acquisition OpSw21, OpSw22, OpSw23 OpSw24 OpSw24 OpSw25 OpSw25 OpSw26 OpSw26 are forwarded to the DCC Track Signal * are not forwarded to the DCC track signal Throttle Switch Control Messages OpSw27 - the "Bushby" bit Switch and Sensor Interrogation Messages at Power-Up are OpSw28 OpSw29 OpSw29 OpSw30 OpSw30 OpSw31 OpSw31 OpSw32 OpSw32 will not restore to prior state at power-on will restore to prior state at power-on * Track Power OpSw33 Restores to "Idle" state Restores to "Run" state if was in "Run" state at power-down * Track Power OpSw34 OpSw35 OpSw35 Normal * Clear all mobile decoder and consist info (see Note) OpSw36 OpSw36 - May require power-cycle to take effect OpSw37 OpSw37 OpSw38 OpSw38 Normal * Clears all Command Station Internal memory and status (see Note) OpSw39 OpSw39 - May require power-cycle to take effect OpSw40 OpSw40 OpSw41 OpSw41 OpSw42 OpSw42 LocoNet Update of Command Station's Track Status is OpSw43 OpSw44 OpSw44 Command Station Switch State Reply is OpSw45 OpSw46 OpSw46 OpSw47 OpSw47 OpSw48 OpSw48 OpSw49 OpSw49 OpSw50 OpSw50 OpSw51 OpSw51 OpSw52 OpSw52 OpSw53 OpSw53 OpSw54 OpSw54 OpSw55 OpSw55 OpSw56 OpSw56 OpSw57 OpSw57 OpSw58 OpSw58 OpSw59 OpSw59 OpSw60 OpSw60 OpSw60 OpSw60 OpSw61 OpSw61 OpSw62 OpSw62 OpSw63 OpSw63 OpSw64 OpSw64 Basic <html><span style="color: black;"><h3><strong> Basic Operating Mode</strong></h3></html> <html><span style="color: black;"><h3><strong> Slot "Purging" Management</strong></h3></html> <html><span style="color: black;"><h3><strong> Locomotive and Slot Management</strong></h3></html> <html><span style="color: black;"><h3><strong> New Locomotive Management</strong></h3></html> <html><span style="color: black;"><h3><strong> Switch Control Message Management</strong></h3></html> <html><span style="color: black;"><h3><strong> LocoNet Track Status Management</strong></h3></html> <html><span style="color: black;"><h3><strong> Throttle Management</strong></h3></html> <html><span style="color: black;"> <strong>* - Indicates the "Factory Default" setting </strong></html> Track Outputs Control <html><span style="color: black;"><h3><strong> Track Output Management</strong></h3></html> <html><span style="color: black;"><h3><strong> Programming Track Output Management</strong></h3></html> Internal Storage Clearing <html><span style="color: black;"> <h2><strong>Command Station Internal Storage Clearing Functions </strong></h2></html> <html></strong><h3>NOTE:</h3> In order for these operations to take effect, it may be necessary to remove command<p> station power.<p> <p> Note also that JMRI's LocoNet Slot Monitor does not recognize the these Command Station OpSw<p> operations which can clear the slots. It is best to shut down JMRI and re-start after<p> clearing the Command Station slot table via OpSw 36 or OpSw39 mechanisms.</html> Reserved OpSws These OpSw ought not be changed from factory default settings. The OpSw settings below cannot be changed by this tool. <html><span style="color: black;"> <strong>* - Indicates the "Factory Default" setting </strong></html> OpSws <html>The "CV" column in the table above shows "OpSw" numbers, where the value "csOpSw." <p>is pre-pended to the OpSw Number. <html> <p><p>OpSw value 0 = "T"hrown. OpSw value 1 = "C"losed.<p> </html></html> Notes <html><span style="color: black;"> <h2><strong>Notes on DCS50 and DCS51 OpSw Settings </strong></h2></html> <html></strong><ul> <li> When manipulating OpSws 36 and/or 39, for the purpose of clearing internal storage of slots and <p> other resources, it may benecessary to power-cycle the command station after writing the the OpSw <p> to the "C"losed state. The command station may fail to act upon the request if one of these operations <p> is not done.<p> <li> Note that JMRI's LocoNet Slot Monitor does not recognize the Command Station OpSw operations which can<p> clear the slots.<p> It is best to shut down JMRI and re-start after clearing the Command Station slot table using OpSw<p> mechanisms.</li> </ul></html> CVs CV CV-Tabelle Taula-CV Tabulka CV CV-tabel This sheet intentionally un-populated. See the "OpSws" tab.