LOCONETOPSBOARD Version ge 1 Servo16 lt 24 Version ge 49 Version ge 50 Version ge 51 Version ge 52 Version lt 51 ServoMain eq 0 ServoAux eq 0 Version ge 51 ServoMain ne 0 ServoAux ne 0 ServoExp ne 0 ServoMain ne 0 ServoAux ne 0 ServoExp ne 0 ServoAux eq 0 Report DCC Change ne 0 Version ge 1 Restore All CVs to Factory Defaults. Device Address=11000 Restore Addresses to Factory Defaults. Device Address=11000 Restore Servo and Input CVs to Factory Defaults. Quad-LN_S Board Address Servo Start Address Turnout Start Address Lock Start Address Main IO Start Address Aux IO Start Address SERVO Turnout Start Address MAIN Turnout Start Address AUX Turnout Start Address EXP Turnout Start Address SERVO Lock Start Address MAIN Lock Start Address AUX Lock Start Address EXP Lock Start Address SERVO Lock Address MAIN Lock Address AUX Lock Address EXP Lock Address MAIN Input Start Address AUX Input Start Address DCC Input Address EXPANSION PORT Mode MAIN and AUX IO PORTS Mode Route Delay Servo OFF When Stopped Servo State Memory Turnout State Memory Signal State Memory Retry on DCC Busy Output Off Switch Request No Command Station Input Invert Blink indicates Unlock Broadcast Local Actions Disable Statonary Interrogate Enable CV7 Interrogate Refresh Servos Only Repower Servo On Change Lock Disables LocoNet Control One Lock Per Port Servo Soft Start Report DCC Change Tam Valley Depot (N3IX Engineering) Quad-LN_S Product ID Hardware revision number Hardware Version Firmware major version number Firmware Version Firmware minor version number . Firmware build number Build Number Version eq 0 <html>ACTION REQUIRED: The installed FIRMWARE VERSION must be READ from the Quad-LN_S</html> Note: the Quad-LN_S Board Address must match the Board Address in this Roster Entry. See below. <html>Reading the Quad-LN_S Firmware Version</html> * OPEN this roster entry using "Programming on Main" (Ops Mode Programmer). * Go to the Quad-LN_S Tab. * If you need to change the Board Address in this Roster Entry then Save, Close and Reopen the Roster Entry. * Do a "Read full sheet". * When the Read is finished this message will disappear. * SAVE the Roster Entry. Note: if JMRI shows Programming Errors while Reading, STOP the Read and confirm that the Quad-LN_S Board Address is programmed properly. <html>Programming the Board Address in the Quad-LN_S to match this Roster Entry</html> * Ensure that there is no loco on your programming track. * OPEN this Roster Entry using "On Programming Track" (Service Mode Programmer). (If Quad-LN_S firmware 3.3 or later is installed you can also use "Programming On Main" (Ops Mode Programmer) when setting the board address.) * Install the ADDR JUMPER on the Quad-LN_S. * Observe that the LEDs on the Quad-LN_S are flashing. * Go to the CV TAB, then WRITE CV17 and WRITE CV18 in that order. * Confirm that the LEDs on the Quad-LN_S have stopped flashing. * REMOVE the ADDR JUMPER. * CLOSE the Roster Entry. You are now done using "On Programming Track" (Service Mode Prgrammer) for this Quad-LN_S. Use "Program On Main" (Ops Mode Programmer) anytime you wish to change settings (other than the Board Address) on this QuadLN_S. Version ge 1 Major Version le 2 FIRMWARE VERSION 3.0 OR LATER IS REQUIRED TO USE THE Quad-LN_S_v3 TEMPLATE. DO A READ SHEET. IF THIS MESSAGE IS STILL PRESENT THEN USE THE Quad-LN_S_v1 TEMPLATE OR UPDATE YOUR FIRMWARE. Major Version ge 3 FIRMWARE VERSION 3.0 REQUIRES USE OF THE Quad-LN_S_v3 TEMPLATE. DO A READ SHEET. IF THIS MESSAGE IS STILL PRESENT THEN USE THE Quad-LN_S_v3 TEMPLATE. Major Version lt 2 Firmware version 2.0 or later is required when using the Detector Board. Do a Read Sheet. If this message is still present then update your firmware if you wish to use the Detector Board. Decoder Template File Version: 3.04.0 Decoder Transform File Version: x.xx.x Basic Group 1/4 Servo16 eq 0 Version ge 1 Group 2/4 Servo16 eq 0 Version ge 1 Group 3/4 Servo16 eq 0 Version ge 1 Group 4/4 Servo16 eq 0 Version ge 1 Group 1 Servo16 ne 0 Group 2 Servo16 ne 0 Group 3 Servo16 ne 0 Group 4 Servo16 ne 0 Group 5 Servo16 ne 0 Group 6 Servo16 ne 0 Group 7 Servo16 ne 0 Group 8 Servo16 ne 0 Group 9 Servo16 gt 8 Group 10 Servo16 gt 8 Group 11 Servo16 gt 8 Group 12 Servo16 gt 8 Group 13 Servo16 eq 25 Group 14 Servo16 eq 25 Group 15 Servo16 eq 25 Group 16 Servo16 eq 25 Routes Version ge 1 LED 1-12 Expansion eq 1 LED 13-24 Expansion eq 1 Aspect 1-8 Version ge 1 Aspect 9-16 Version ge 1 Aspect 17-24 Version ge 1 Aspect 25-32 Version ge 1 Aspect 33-40 Version ge 1 Aspect 41-48 Version ge 1