LOCONETBDOPSWMODE Board ID Outputs are pulsed (OpSw1=t) Thrown is first choice; Closed is second choice Outputs are static (OpSw1=c) Thrown is first choice; Closed is second choice Outputs pulse active or blink for 0.1 second (OpSw2=t) Outputs pulse active or blink for 0.2 second (OpSw2=c) Add 0 seconds to the pulse or blink rate (OpSw3=t) Add 0.3 seconds to the pulse or blink rate (OpSw3=c) Add 0 seconds to the pulse or blink rate (OpSw4=t) Add 0.7 seconds to the pulse or blink rate (OpSw4=c) Add 0 seconds to the pulse or blink rate (OpSw5=t) Add 1.5 seconds to the pulse or blink rate (OpSw5=c) Outputs automatically power-up to the last known state (OpSw6=t) Thrown is first choice; Closed is second choice Each output remain undriven until its turnout command is received (OpSw6=c) Thrown is first choice; Closed is second choice Short delay for interrogation requests (OpSw8=t) Thrown is first choice; Closed is second choice Long delay for interrogation requests (OpSw8=c) Thrown is first choice; Closed is second choice Static Outputs remain powered (OpSw9=t) Thrown is first choice; Closed is second choice Static Outputs are shut off after 16 seconds (OpSw9=c) Thrown is first choice; Closed is second choice Throttle and Computer commands are accepted (OpSw10=t) Thrown is first choice; Closed is second choice Computer commands are accepted (OpSw10=c) Thrown is first choice; Closed is second choice Routes are triggered by Switch commands from Computers or Throttles (OpSw11=t) Thrown is first choice; Closed is second choice Routes are triggered by DS64 inputs (OpSw11=c) Thrown is first choice; Closed is second choice S inputs affect output; A inputs send Sensor messages (OpSw12=t) Thrown is first choice; Closed is second choice A input high forces output "Thrown"; S input high forces output "Closed" (OpSw12 = c) Thrown is first choice; Closed is second choice Inputs have no effect (OpSw13=t) Thrown is first choice; Closed is second choice Inputs act as LocoNet Sensors and also control related outputs per OpSw12 (OpSw13=c) Thrown is first choice; Closed is second choice Accepts commands from LocoNet messages and Track (OpSw14=t) Thrown is first choice; Closed is second choice Accepts commands from Track only (OpSw14=c) Thrown is first choice; Closed is second choice Inputs can control outputs (OpSw15=t) Thrown is first choice; Closed is second choice Inputs have no direct effect on outputs (OpSw15=c) Thrown is first choice; Closed is second choice Routes are Output 1 does not provide "crossing-gate" output (OpSw17=t) Thrown is first choice; Closed is second choice Output 1 provides "crossing-gate" output (OpSw17=c) Thrown is first choice; Closed is second choice Output 2 does not provide "crossing-gate" output (OpSw18=t) Thrown is first choice; Closed is second choice Output 2 provides "crossing-gate" output (OpSw18=c) Thrown is first choice; Closed is second choice Output 3 does not provide "crossing-gate" output (OpSw19=t) Thrown is first choice; Closed is second choice Output 3 provides "crossing-gate" output (OpSw19=c) Thrown is first choice; Closed is second choice Output 4 does not provide "crossing-gate" output (OpSw20=t) Thrown is first choice; Closed is second choice Output 4 provides "crossing-gate" output (OpSw20=c) Thrown is first choice; Closed is second choice Inputs generate LocoNet "General Sensor" messages (OpSw21=t) Thrown is first choice; Closed is second choice Inputs generate LocoNet "LocoNet Turnout State" messages (OpSw21=c) Thrown is first choice; Closed is second choice Outputs pulse or blink at DS64 Routes Local Inputs OpSws Short Address gt 0 <html>The "CV" column in the table above shows "OpSw" numbers, where the value "115." is pre-pended <p>to the OpSw Number. For example, PM4/PM42 OpSw 1 is represented as "115.01". <p><p>The top-most row above reflects the Board Address configured on the "Basic" sheet. <p><p>OpSw value 0 = "T"hrown. OpSw value 1 = "C"losed. </html> Basic <html><p> LocoNet messaging limits the supported Board ID range to addresses between 1 and 128. This tool cannot access DS64s <p>outside of this range. <p> <p>This roster entry will only access the specified DS64 if the Board ID, on the "Basic" sheet, is correct when the <p>programmer is opened. <p> <p>If the Board ID has been changed since the programmer was opened, the programmer will attempt to access the <p>DS64 address which was specified in the Roster entry when the progammer was opened. <p> <p>After making a change to the Roster entry's Board ID (Active Address) on the "Basic" sheet, save and close the programmer <p>window and re-open the Roster entry to ensure that the the programmer will use the modified Active Address for accesses <p>to the device. <p>Note that BDL16x and PM4x documentation refers to Board Address, while DS64 and SE8C documentation refers to <p>Board ID. These are equivalent concepts. </html> DS64 Basic Settings <html><span style="color: black;"><h2><strong>Output Controls Characteristics</strong></h2></html> <html><span style="color: black;"><h2><strong>Control Source Characteristics</strong></h2></html> <html><span style="color: black;"><h2><strong>Local Routes Characteristics</strong></h2></html> <html><span style="color: black;"><h2><strong>Local Input Signals Characteristics</strong></h2></html> Notes <html><span style="color: black;"> <h2><strong>Notes on DS64 Roster Entries and Programming </strong></h2></html> <html></strong><p><ul> <li> The DS64 <em>must</em> be in its normal operating mode in order to respond to this Roster entry's read and write operations.</li> <li> <p>See the "Basic" sheet for the programmer's limitations with respect to Board ID.</li> <li><p>This Roster entry is not currently capable of displaying, changing, or saving the DS64 output addresses.</p></li> <li><p>This Roster entry is not currently capable of displaying, changing, or saving the DS64 Routes.</p></li> </ul></html> CVs CV CV-Tabelle Taula-CV Tabulka CV CV-tabel Short Address eq 0 This sheet intentionally un-populated. See the "OpSws" tab.