LOCONETCSOPSWMODE OpSw 01 OpSw 01 DCS52 acts as a OpSw 02 Autoreversing is OpSw 03 OpSw 04 OpSw 04 OpSw 05 OpSw 05 OpSw 06 OpSw 06 OpSw 07 OpSw 07 OpSw 08 OpSw 08 OpSw 09 OpSw 09 OpSw 10 OpSw 10 OpSw 11 OpSw 11 OpSw 12 OpSw 12 Locomotive Purge is OpSw 14 OpSw 014 eq 0 Purge time is OpSw 13 OpSw 014 eq 0 Locomotive Purging will OpSw 15 OpSw 16 OpSw 16 OpSw 17 OpSw 17 OpSw 18 OpSw 18 OpSw 19 OpSw 19 Address 00 'Analog stretching' (or conventional locos) is OpSw 20 Global System Loco "Speed-step Mode" Default for New Loco Acquisition OpSw21, OpSw22, OpSw23 OpSw 24 OpSw 24 OpSw 25 OpSw 25 OpSw 26 OpSw 26 "Normal" Switch commands OpSw 27 Interrogation of turnouts and sensors at power on is OpSw 28 OpSw 29 OpSw 29 OpSw 30 OpSw 30 Route/switch message output rate is OpSw 31 - the speed at which turnout commands are propagated to the DCC track signal OpSw 32 OpSw 32 OpSw 33 OpSw 33 OpSw 34 OpSw 34 'Reset' button is OpSw 35 OpSw 36 OpSw 36 OpSw 37 OpSw 37 DCS52 Loco Reset Button OpSw 38 OpSw 39 OpSw 39 OpSw 40 A Factory Reset operation can be performed using the DCS52 keyboard via its "Option Switch Setup" feature. JMRI cannot perform this "programmatically". Diagnostic 'click' on incoming LocoNet activity and Route activation OpSw 41 Two "short beep" indication of loco 'purging' is OpSw 42 LocoNet slot write update of command station's track status is OpSw 43 OpSw 44 OpSw 44 OpSw 45 OpSw 45 OpSw 46 OpSw 46 OpSw 47 OpSw 47 OpSw48 OpSw49 OpSw50 OpSw51 OpSw52 OpSw53 OpSw54 OpSw55 OpSw56 OpSw57 OpSw58 OpSw59 OpSw60 OpSw61 OpSw62 OpSw63 OpSw64 OpSw65 OpSw66 OpSw67 OpSw68 OpSw69 OpSw70 OpSw71 OpSw72 OpSw73 OpSw74 OpSw75 OpSw76 OpSw77 OpSw78 OpSw79 OpSw80 OpSw81 OpSw82 DCS52 Jump Ports are OpSw 83 OpSw84 OpSw85 OpSw86 OpSw87 OpSw88 OpSw89 OpSw90 OpSw91 OpSw92 OpSw93 OpSw94 OpSw95 OpSw96 Basic <html><span style="color: black;"><h3><strong> Basic Operating Mode</strong></h3></html> <html><span style="color: black;"><h3><strong> Slot "Purging" Management</strong></h3></html> <html><span style="color: black;"><h3><strong> New Locomotive Management</strong></h3></html> <html><span style="color: black;"><h3><strong> Jump Port Management</strong></h3></html> <html><span style="color: black;"><h3><strong> Switch Control Message Management</strong></h3></html> <html><span style="color: black;"><h3><strong> Command Station Sounds Management</strong></h3></html> <html><span style="color: black;"><h3><strong> LocoNet Track Status Management</strong></h3></html> <html><span style="color: black;"> <strong>* - Indicates the "Factory Default" setting </strong></html> Track Outputs Control <html><span style="color: black;"><h3><strong> Track Output Management</strong></h3></html> Internal Storage Management <html><span style="color: black;"> <h2><strong>Command Station "Loco Reset" Button Management </strong></h2></html> <html><span style="color: black;"> <h2><strong>Command Station Internal Storage Clearing Functions </strong></h2></html> <html></strong><h3>NOTE:</h3> In order for OpSw36 and/or OpSw39 operations to take effect, it may be necessary to<p> remove command station power or briefly place the command station into "OpSw" mode via its <p> front-panel switch.<p> <p> Note also that JMRI's LocoNet Slot Monitor does not recognize the Command Station OpSw<p> operations which can clear the slots. It is best to shut down JMRI and re-start after<p> clearing the Command Station slot table via OpSw 36 or OpSw39 mechanisms.</html> JMRI cannot programmatically modify DCS52 OpSw40. Use a throttle with the DCS52 in "OpSw" mode. Reserved OpSws These OpSw ought not be changed from factory default settings. The OpSw settings below cannot be changed by this tool. <html><span style="color: black;"> <strong>* - Indicates the "Factory Default" setting </strong></html> OpSws <html>The "CV" column in the table above shows "OpSw" numbers, where the value "csOpSw." <p>is pre-pended to the OpSw Number. <html> <p><p>OpSw value 0 = "T"hrown. OpSw value 1 = "C"losed.<p> </html></html> Notes <html><span style="color: black;"> <h2><strong>Notes on DCS52 OpSw Settings </strong></h2></html> <html></strong><ul> <li>Several undocumented DCS52 OpSw settings are included here based on trial-and-error testing of effects.</li> <p> <li>When manipulating OpSws 36 or 38, for the purpose of clearing internal <p> storage of slots, consists, memory states, etc., it may be necessary to power-cycle the command station.<p> The command station may fail to act upon the request if one of these operations is not done.</li> <p> <li>Note that JMRI's LocoNet Slot Monitor does not recognize the Command Station OpSw<p> operations which can clear the slots.<p> It is best to shut down JMRI and re-start after clearing the Command Station slot table<p> using OpSw mechanisms.</li> <p;> <li>The 'Global System Loco "Speed-step Mode" Default for New Loco Acquisition' item on the <p> "Basic OpSw Settings" 'Sheet' will not be "colorized" to reflect the state of OpSw21,<p> OpSw22 and OpSw23, due to limitations of JMRI's mechanisms.</li> </ul></html> CVs CV CV-Tabelle Taula-CV Tabulka CV CV-tabel This sheet intentionally un-populated. See the "OpSws" tab.