LOCONETBDOPSWMODE Board Address (Board ID) Direct Home Wiring Whole-layout Common Rail Wiring Wiring type is normal reversed (pay attention to other RailSync wire) LocoNet cabling is Disable Transponding Enable Transponding Enable Transponding Unsupported Enable Transponding Unsupported Transponding is report occupied when zone power is off are not forced when zone power is off Detection Sections is a normal Detection Section is a Zone Power ON qualifier for whole-layout common-rail wired systems Detection Section 16 acts as the LocoNet Master is not the LocoNet Master This BDL16x provides LocoNet termination does not terminate LocoNet This BDL16x Wait for 5-second power-up delay (for DB150 compatibility) Wait for 0.5 second power-up delay This BDL16x will Resistance below about 22K Ohms is shown as Occupied Resistance below about 10K Ohms is shown as Occupied Detection Section Sensitivity: Thrown Closed Thrown Closed Thrown Closed Thrown Closed Sampling of RailSync is BDL16x LED outputs Responds with status at GPON and interrogate commmands Responds only to interrogate commmands Standard interrogation Ignore OpSw36 setting; reply at every interrogation Thrown Closed Thrown Closed Detection Section timing is Sequential Mode Verbose Mode Transponder Tracking uses Thrown Closed Thrown Closed BDL16x LED outputs sends Transponding messages does not send Transponding messages At reception of GPOFF: OpSws Short Address gt 0 <html>The "CV" column in the table above shows "OpSw" numbers, where the value "113." <p>is pre-pended to the OpSw Number. <p><p>The top-most row above reflects the Board Address configured on the "Basic" sheet. <html><p>For example, BDL16 OpSw 1 is represented as "113.01".<p></html> <html><p>For example, BDL162 OpSw 1 is represented as "113.01".<p></html> <html><p>For example, BDL168 OpSw 1 is represented as "113.01".<p></html> <html> <p><p>OpSw value 0 = "T"hrown. OpSw value 1 = "C"losed.<p> </html></html> Basic <html><p> LocoNet messaging limits the supported Board Address (Board ID) range to addresses between 1 and 128. This tool cannot access <p>BDL16x devices outside of this range. <p> <p>This roster entry will only access the specified BDL16x if the Board Address (Active Address), on the <p>"Basic" sheet, is correct when the programmer is opened. <p> <p>If the Board Address (Active Address) has been changed since the programmer was opened, the programmer will attempt to access the <p>BDL16x address which was specified in the Roster entry when the progammer was opened. <p> <p>After making a change to the Roster entry's Board Address (Active Address) on the "Basic" sheet, save and close the programmer <p>window and re-open the Roster entry to ensure that the the programmer will use the modified Active Address for accesses <p>to the device. <p> <p>Note that BDL16x and PM4x documentation refers to Board Address, while DS64 and SE8C documentation refers to <p>Board ID. These are equivalent concepts. </html> Basic OpSw Settings <html><span style="color: black;"><h2><strong>Detection Characteristics</strong></h2></html> <html><span style="color: black;"><h2><strong>LocoNet Characteristics</strong></h2></html> <html><span style="color: black;"><h2><strong>LED Output Characteristics</strong></h2></html> Transponding Controls <html><span style="color: black;"><h2><strong>Transponding Characteristics</strong></h2></html> Notes <html><span style="color: black;"> <h2><strong>Notes on BDL16 Roster Entries and Programming </strong></h2></html> <html></strong><ul> <li>The BDL16 <em>must</em> be in its normal operating mode in order to respond to this Roster entry's read and write operations.</li> <li> <p>See the "Basic" sheet for the programmer's limitations with respect to Board Address.</li> </ul></html> <html><span style="color: black;"> <h2><strong>Notes on BDL162 Roster Entries and Programming </strong></h2></html> <html></strong><ul> <li>The BDL162 <em>must</em> be in its normal operating mode in order to respond to this Roster entry's read and write operations.</li> <li> <p>See the "Basic" sheet for the programmer's limitations with respect to Board Address.</li> </ul></html> <html><span style="color: black;"> <h2><strong>Notes on BDL168 Roster Entries and Programming </strong></h2></html> <html></strong><ul> <li>The BDL168 <em>must</em> be in its normal operating mode in order to respond to this Roster entry's read and write operations.</li> <li> <p>See the "Basic" sheet for the programmer's limitations with respect to Board Address.</li> </ul></html> CVs CV CV-Tabelle Taula-CV Tabulka CV CV-tabel Short Address eq 0 This sheet intentionally un-populated. See the "OpSws" tab.