Files
FilaMan-System-ESP32/src/config.cpp
T
ManuelW77andClaude Opus 5 a5ba8a901a Make WiFi TX power configurable, document ESP32-S3 pins
The transmit power was hardcoded to 19.5 dBm. Some setups need a lower
value (device right next to the AP, weak 3.3V rail), so it is now a user
setting instead of a per-chip constant.

- wlan.cpp: load/save/apply TX power (0.1 dBm steps, NVS key wifi_txpwr,
  default 195), re-applied on GOT_IP so it survives a reconnect
- website.cpp: /api/wifi-power GET/POST with validation
- setup.html: "WiFi Settings" card
- README.md/README.de.md: pin table gets an ESP32-S3 column plus a warning
  that GPIO19/20 are the native USB data lines
- config.cpp: same warning next to the HX711 pin definitions

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
2026-09-20 12:42:13 +02:00

81 lines
2.0 KiB
C++

#include "config.h"
// ################### Config Bereich Start
// ***** PN532 (RFID)
//#define PN532_SCK 18
//#define PN532_MOSI 23
//#define PN532_SS 5
//#define PN532_MISO 19
#if CONFIG_IDF_TARGET_ESP32S3
const uint8_t PN532_IRQ = 15;
const uint8_t PN532_RESET = 16;
#else
const uint8_t PN532_IRQ = 32;
const uint8_t PN532_RESET = 33;
#endif
// ***** PN532
// ***** HX711 (Waage)
// HX711 circuit wiring
// ACHTUNG ESP32-S3: GPIO19/20 sind die nativen USB-Leitungen (D-/D+) und liegen auf
// dem DevKitC-1 an der "USB"-Buchse. Der HX711 wird dort unzuverlaessig erkannt.
// Pins hier nur zusammen mit den Tabellen in README.md / README.de.md aendern.
#if CONFIG_IDF_TARGET_ESP32S3
const uint8_t LOADCELL_DOUT_PIN = 5;
const uint8_t LOADCELL_SCK_PIN = 6;
#else
const uint8_t LOADCELL_DOUT_PIN = 16;
const uint8_t LOADCELL_SCK_PIN = 17;
#endif
const uint8_t calVal_eepromAdress = 0;
const uint16_t SCALE_LEVEL_WEIGHT = 500;
// ***** HX711
// ***** TTP223 (Touch Sensor)
// TTP223 circuit wiring
#if CONFIG_IDF_TARGET_ESP32S3
const uint8_t TTP223_PIN = 7;
#else
const uint8_t TTP223_PIN = 25;
#endif
// ***** TTP223
// ***** Display
const uint8_t OLED_TOP_START = 0;
const uint8_t OLED_TOP_END = 16;
const uint8_t OLED_DATA_START = 17;
const uint8_t OLED_DATA_END = SCREEN_HEIGHT;
// ***** Display
// ***** Webserver
const uint8_t webserverPort = 80;
// ***** Webserver
// ***** API
String filamanUrl = "";
String filamanToken = "";
bool filamanRegistered = false;
// ***** API
// ***** Display Sleep
uint16_t oledSleepTimeout = 60; // Default 60 seconds (0 = disabled)
// ***** Display Sleep
// ***** WiFi
// Sendeleistung in 0.1 dBm. Default 19.5dBm = Maximum; nur senken, wenn der AP
// das Geraet rauswirft (reason=2/4) oder es direkt neben dem AP steht.
int16_t wifiTxPowerDeciDbm = 195;
// ***** WiFi
// ***** Task Prios
uint8_t rfidTaskCore = 1;
uint8_t rfidTaskPrio = 1;
uint8_t rfidWriteTaskPrio = 1;
uint8_t scaleTaskCore = 0;
uint8_t scaleTaskPrio = 1;
// ***** Task Prios