Recupération projet
This commit is contained in:
1 parent
b2d99a5fbc
commit
4102675b10
52 files changed
+56644
No files matched your search
@@ -0,0 +1,77 @@
|
||||
# DCC-Lokdecoder
|
||||
## Description
|
||||
DCC multifunction decoder for H0 locomotives
|
||||
## Features
|
||||
- 1 motor H-bridge output
|
||||
- 3.6 A peak current
|
||||
- PWM frequency configurable (1-40 kHz)
|
||||
- overcurrent and temperature protected
|
||||
- 10 function outputs
|
||||
- 115 mA per output
|
||||
- F0f, F0r, AUX1 and AUX2 are dimmable *todo*
|
||||
- mappable to F0-F12 function keys
|
||||
- DCC asymmetry can be detected (for automatic brake control) *todo*
|
||||
## Hardware
|
||||
- 4-layer PCB esigned in KiCAD
|
||||
- fairly standard components (available from Digi-Key, Farnell, Mouser, etc...)
|
||||
- hand solderable (I did it too)
|
||||
- 4 debug LEDs (red, yellow, green and blue)
|
||||
|
||||
|  |  |
|
||||
| :---: | :---: |
|
||||
| top side | bottom side |
|
||||
|
||||
|
||||
|
||||
## Firmware
|
||||
- Arduino compatible programming (behaves like an UNO)
|
||||
- DCC decoding by [NmraDcc](https://github.com/mrrwa/NmraDcc) library
|
||||
|
||||
## JMRI integration
|
||||
|
||||
|  |  |  |  |  |  |
|
||||
| :---: | :---: | :---: | :---: | :---: | :---: |
|
||||
| Basic | Motor | Basic speed control | Speed table | Function map | Advanced |
|
||||
|
||||
## Install guide
|
||||
|
||||
1. Get the PCB (e.g. [JLCPCB](https://jlcpcb.com/)) and the components (e.g. [mouser](https://www.mouser.at/), [digikey](https://www.digikey.at/))
|
||||
2. Solder the components. The SOIC with exposed pad is a bit tricky, it can be soldered from the other side with a big tip and a lot of flux.
|
||||
3. Install the Arduino bootloader using the pads 5V, GND, SCK, MISO, MOSI, RST and an Arduino. [Arduino as ISP](https://www.arduino.cc/en/Tutorial/BuiltInExamples/ArduinoISP)
|
||||
4. Uncomment the line `#define RESET_FACTORY_DEFAULTS` to fill the EEPROM with the default CV values
|
||||
5. Upload the code using the pads 5V, GND, RX, TX, DTR and a USB TTL UART cable [like this](https://www.mouser.at/ProductDetail/FTDI/TTL-232R-5V-WE/?qs=OMDV80DKjRpCUAS6UR9QpQ%3D%3D)
|
||||
6. Re-comment the line `#define RESET_FACTORY_DEFAULTS` to avoid resetting to factory defaults every time.
|
||||
7. Upload the code again.
|
||||
8. Add the decoder XML file to JMRI. In DecoderPro select "File-> Import Decoder File..." and browse to the decoder [XML](JMRI_decoder_file/Public_Domain_GTI_green.xml). It will take some time, then adds the decoder definition to the database.
|
||||
9. Connect the T1 and T2 pads to the programming track of your DCC system.
|
||||
10. Add new locomotive with the "New Loco" button and then "Read type from decoder". It should detect the correct type:
|
||||

|
||||
11. If everything is fine, you can install the decoder into your locomotive!
|
||||
### Pinout
|
||||
| Pad | Function |
|
||||
| :-- | :-- |
|
||||
| M1 | Motor 1 |
|
||||
| M2 | Motor 2 |
|
||||
| T1 | Track 1 |
|
||||
| T2 | Track 2 |
|
||||
| V+ | Positive common for function outputs (keep-alive capacitor positive) |
|
||||
| F0f | F0 function output forward (open drain) |
|
||||
| F0r | F0 function output reverse (open drain) |
|
||||
| 1-8 | AUX function output n (open drain) |
|
||||
| 5V | internal microcontroller +5V supply |
|
||||
| GND | ground (keep alive capacitor negative) |
|
||||
| SCK | ISP programming clock (connect to ISP SCK) |
|
||||
| MISO | ISP programming read (connect to ISP MISO) |
|
||||
| MOSI | ISP programming write (connect to ISP MOSI) |
|
||||
| RST | ISP programming reset (connect to ISP reset output)
|
||||
| RX | serial programming receive (connect to TTL UART TX) |
|
||||
| TX | serial programming transmit (connect to TTL UART RX) |
|
||||
| DTR | serial programming reset through a 100 nF capacitor (connect to TTL UART DTR) |
|
||||
|
||||
## Todo list
|
||||
- [ ] CV15, CV16 decoder locking
|
||||
- [ ] CV65 kick start
|
||||
- [ ] CV67-94 speed table
|
||||
- [ ] CV27 automatic brake control
|
||||
- [ ] function output dimming
|
||||
- [ ] motor fault check
|
||||
Reference in new issue
Block a user